Idiomas disponibles
Idiomas disponibles
Original translation
Post - Gas
Self
Reset
SEMI-AUTOMATIC STEEL / STAINLESS STEEL WELDING (MAG)
The device is suitable for welding 0.6/0.8/1.0 steel wire and 0.8/1.0 stainless steel wire.
The device is delivered with contact tip, liner and a torch set up for 0.8 steel or stainless steel wire. For welding 0.6 wire use a torch
no longer than 3m. To change the contact tip (see fig II A). The roller is reversible 0.8/1.0. The indication on the visible side of the
roller is the diameter in use. For a 0.6 wire use the 0.6 groove.
Welding Steel or Stainless Steel requires using a specific gas mix - Argon + CO2 (Ar + CO2). The proportion of CO2 will vary
depending on application. The gas flow for steel welding is between 8 and 12 L/min depending on the environment and experience
of the welder. For specific requirements seek advice from your gas distributor.
For polarity see page 3.
SEMI-AUTOMATIC ALUMINIUM WELDING (MIG)
This welding machine is suitable for welding 0.8 and 1mm aluminium wires .
To weld aluminium, neutral gas "Pure Argon" (AR) is required. For choosing gas, ask a gas distributor for advice. The gas flow for
welding aluminium is between 15 and 25 L/min depending on the environment and experience of the welder.
Machine set-up for aluminium welding:
- Use specific rollers for Aluminium
- Set the pressure on the rollers to the minimum to avoid pinching the wire.
- Remove the capillary tube before connecting the aluminium torch with a teflon liner.
- When welding aluminium use a special aluminium torch with Teflon liner to reduce friction. Do not cut the liner near the connector!
It is used to guide the wire from the rollers. (Fig II B)
- Contact Tip: Use a SPECIAL aluminium contact tip corresponding to the diameter of the wire.
For polarity see page 3.
"NO GAS" WELDING
To set up this use, refer to the indications on page 4.
The device is designed to weld «No gas» cored wire from Ø0.9 to Ø1.2 mm.
No gas» use requires the use of a specific roller compatible with the welding unit:
Roller type B for cored wire Ø0.9 to Ø1.2 mm.
Welding flux-cored wire with a standard nozzle can lead to overheating and damage to the torch. Preferably use a special «No
Gas» nozzle (ref. 041868), or remove the original nozzle (Fig. III D).
For polarity, refer to page 3.
PROCEDURE FOR CHANGING REELS AND TORCH ASSEMBLY (FIG IV)
• Remove the nozzle from the torch (fig E) and the contact tip (fig D).
• Open the machine's side door.
• Place the reel on the driving pin (fig A) of the reel support. For a 200mm wire reel tighten the reel to the maximum. The adaptor
(1) is only to be used for a 200mm reel.
• Adjust the reel brake (2) to avoid the reel inertia tangling the wire when welding stops. In general, do not over-tighten! Then screw
in the reel support (3).
HM200MP
Hold down buttons 1 and 2 and use the upper
knob to select «POG». Use the lower knob to
move the cursor to the setting. Use the upper
knob again to adjust the Post Gas from 0 ms to
1 000 ms (in 100 ms steps).
The default setting is 300 ms.
Hold down buttons 1 and 2 and use the upper
knob to select «SLF». Use the lower knob to
move the cursor to the setting. Use the upper
knob again to adjust the self from 10 to 90 (in
10 steps). The default setting is 50.
Caution! The reset is activated by setting
its value to ON. A countdown of 3s starts. Once
it has reached 0, the reset takes place and the
product is restarted. On the interface and the
secondary menu, the default settings/values
apply again.
+
+
+
EN
11
