Idiomas disponibles
Idiomas disponibles
6.2 Fitting/changing the table insert (Fig. 7-8)
•
To prevent increased likelihood of injury, the
table insert should be changed whenever it is
worn or damaged.
•
Take off the saw blade guard (2) (see 6.4).
•
Place the 10 mm side of one of the two ring
wrenches (30/31) on the rotary disk (13). Turn
the disk (13) counterclockwise with the ring
wrench to release the table insert.
•
Take out the worn table insert (6).
•
Fit the replacement table insert by following
the above in reverse.
6.3 Fitting/replacing the riving knife
(Fig. 9-13)
•
Danger! Remove the rechargeable battery
from the equipment!
•
Remove the saw blade guard (2) and the tab-
le insert (6) (see 6.4, 6.2).
•
Using the hand wheel (8) set the blade (4) to
max. cutting depth, move to 0° position and
lock in place.
•
Slacken the fastening screw (19) until the gap
between the fastening plate (20) and the sup-
port surface opposite is approx.
Caution! Do not completely undo the faste-
ning plate (20).
•
Insert the riving knife (5) in the gap, push it
right down as far as it goes and then secure it
with the fastening screw (19). Make sure that
the riving knife has been fitted straight and
not wobbly.
•
The riving knife (5) must be positioned in
the center along an imaginary line extending
behind the saw blade (4), so that it is not pos-
sible for the material to get jammed.
•
The gap between the blade (4) and the riving
knife (5) should be
(Fig. 12).
•
Refit the table insert (6) and the saw blade
guard (2) (see 6.2, 6.4)
6.4 Fitting/changing the saw blade guard
(Fig. 14)
•
Mount the saw blade guard (2) on the riving
knife (5) so that the screw fits through the
hole (18) in the riving knife.
•
Then insert the screw on the saw blade guard
(2) through the hole (18) and tighten it.
•
Important! The maximum depth that the
screw can be screwed in has been preset at
the factory, so that the saw blade guard (2) is
always able to move freely.
•
Warning! The saw blade guard (2) must al-
ways lower to the workpiece automatically
under its own weight.
Anl_TE_TS_36_210_Li_USA_SPK7.indb 21
Anl_TE_TS_36_210_Li_USA_SPK7.indb 21
⁄
" (5 mm).
3
16
⁄
" to
⁄
" (3 - 8 mm).
3
5
32
16
- 21 -
EN
6.5 Fitting/changing the saw blade (Fig. 15)
•
Before changing the saw blade: Remove the
rechargeable battery from the equipment!
•
Wear work gloves to prevent injury when
changing the saw blade.
•
Using the hand wheel (8), set the saw blade
(4) to the maximum cutting depth.
•
Remove the saw blade guard, table insert
and riving knife (see 6.4, 6.2, 6.3).
•
Undo the screw (15) with a wrench (30) on
the screw (15) itself and a second wrench
(31) on the motor shaft to apply counter-
pressure.
•
Caution! Turn the screw (15) in the direction
of rotation of the saw blade.
•
Take off the outer flange and pull the old saw
blade (4) off the inner flange.
•
Clean the blade flange thoroughly before fit-
ting the new blade.
•
Fit and fasten the new saw blade (4) in rever-
se order.
•
Important! Note the running direction. The
cutting angle of the teeth must point in run-
ning direction, i.e. forwards (see the arrow on
the blade guard).
•
Refit and set the riving knife, table insert and
saw blade (see 6,3, 6.2, 6.4).
•
Check to make sure that all safety devices
are properly mounted and in good working
condition before you begin working with the
saw again.
•
Warning! Every time that you change the saw
blade, check that the saw blade guard (2)
opens and closes again in accordance with
requirements. Also check that the saw blade
(4) spins freely in the saw blade guard (2).
•
Warning! Every time that you change the saw
blade (4), check to see that it spins freely in
the table insert (6) in both perpendicular and
45° angle settings.
•
Warning! You should replace the table insert
(6) immediately whenever it is worn or dama-
ged (see 6.2).
•
Warning! The work to change and align the
saw blade (4) must be carried out correctly.
6.6 Putting away loose parts (Fig. 4)
When not in use, the miter gauge (14), push stick
(3) and the two wrenches (30/31) can be secured
as shown in Fig. 2.
6.7 Connection for dust extractor (Fig. 16-19)
A connection for a dust extractor is provided on
the extractor adapter on the housing (16) and on
the saw blade guard (2).
07.10.2022 09:39:59
07.10.2022 09:39:59
