Stihl MSA 60.0 C Manual De Instrucciones página 63

21 Bar and Chain Combinations
If the battery is charged, used or stored outside
the recommended temperature ranges, perform‐
ance may be reduced.
If the battery is wet or moist, allow the battery to
dry for at least 48 h between 15°C and 50°C and
with less than 70% humidity. Higher humidity
may extend the drying time.
20.9 Sound Values and Vibration
Values
The K-value for the sound pressure level is
2 dB(A). The K-value for the sound power level is
2 dB(A). K-value for vibration level is 2 m/s².
MSA 60.0 C
STIHL recommends wearing ear defenders.
– Sound pressure level L
to EN 62841‑4‑1: 83 dB(A)
– Sound power level L
EN 62841-4-1: 94 dB(A)
– Vibration level a measured according to
hv
EN 62841-4-1:
– Control handle: 3.4 m/s²
– Front handle: 3.2 m/s².
MSA 70.0 C
STIHL recommends wearing ear defenders.
– Sound pressure level L
to EN 62841‑4‑1: 83 dB(A)
21 Bar and Chain Combinations
21.1 STIHL MSA 60.0 C, MSA 70.0 C Chainsaws
Pitch Drive link
gauge/groove
width
1/4" P 1.1 mm
The cutting length of a guide bar depends on the chainsaw and the saw chain being used. The actual
cutting length of a guide bar may be less than the specified length.
22 Spare Parts and Accesso‐
ries
22.1 Spare parts and accessories
These symbols indicate original STIHL
spare parts and original STIHL acces‐
sories.
STIHL recommends the use of original STIHL
spare parts and accessories.
0458-022-9801-A
measured according
pA
measured according to
wA
measured according
pA
Length Guide bar
25 cm Rolloma‐
tic E Mini /
30 cm
Light 01
30 cm Carving
– Sound power level L
EN 62841-4-1: 94 dB(A)
– Vibration level a measured according to
hv
EN 62841-4-1:
– Control handle: 3.4 m/s²
– Handlebar: 3.2 m/s².
The sound and vibration levels indicated were
measured according to a standardized test
method and can be used as a basis for compar‐
ing electric power tools. The actual sound and
vibration levels may vary from the values indica‐
ted, depending on the type of application. The
sound and vibration levels indicated can be used
for an initial estimate of the sound and vibration
stress. The actual sound and vibration stress has
to be estimated. The times can be taken into
account in the estimate when the electric power
tool is switched off and also when it is switched
on but running without any load.
For information on compliance with Employers'
Vibration Directive 2002/44/EC see
www.stihl.com/vib.
20.10 REACH
REACH is an EC regulation and stands for the
Registration, Evaluation, Authorisation and
Restriction of Chemical substances.
For information on compliance with the REACH
regulation see www.stihl.com/reach.
Number of Number of
teeth, spro‐ drive links
cket nose
8
-
Despite ongoing market observation, STIHL is
unable to judge the reliability, safety and suitabil‐
ity of other manufacturers' spare parts and
accessories; accordingly, STIHL cannot warrant
for the use of those parts.
Original STIHL spare parts and original STIHL
accessories are available from STIHL dealers.
English
measured according to
wA
Saw chain
56
71 PM3 (type
64
3670)
64
63