Metabo WEVF 10-125 Quick Inox Manual Original página 19

workpiece does not become too hot.
Rough grinding: position the machine at an angle of
30° - 40° for the best working results.
Cut-off grinding:
Always work against the run of the disc
(see illustration). Otherwise there is
the danger of the machine kicking
back from the cut out of control. Guide
the machine evenly at a speed
suitable for the material being processed. Do not tilt,
apply excessive force or sway from side to side.
Wire brushing:
Press down the machine evenly.
8.4 Rotate gear housing
See illustration D on page 3.
- Disconnect the mains plug.
- Remove guard (6).
- Unscrew the 4 gear housing screws (a).
CAUTION! Do not remove the gear housing!
- Turn the gear housing to the desired position
without removing it.
- Screw in the 4 gear housing screws (a) in the
available threads! Tightening torque = 3,0 Nm +/-
0,3 Nm.
9. Cleaning
Particles may become deposited inside the power
tool during operation. This impairs the cooling of the
power tool. Conductive build-up can impair the
protective insulation of the power tool and create an
electrical hazard.
The power tool should be cleaned regularly, often
and thoroughly through all front and rear air vents
using a vacuum cleaner or by blowing in dry air.
Prior to this operation, separate the power tool from
the power source and wear protective glasses and
suitable dust mask. Ensure appropriate suction is
available when blowing out vents.
Regularly clean dust filter: remove and blow out
with compressed air.
10. Troubleshooting
- Electronic safety shutdown The electronic
signal display (10) flashes and the machine
was automatically SWITCHED OFF. If the slew
rate of the current is too high (for example, if the
machine suddenly seizes or kickback occurs), the
machine switches off. Switch machine off with
switch. Switch it on again and continue to work as
normal. Try to prevent the machine from seizing.
See chapter 4.2.
Machines with VTC and TC electronics:
The electronic signal display (10) lights
up and the load speed decreases. There is
too much load on the machine! Run the
machine in idling until the electronics signal
indicator switches off.
Machines with VTC, TC and VC electronics:
The electronic signal display (10) flashes
and the machine does not start. The restart
protection is active. If the mains plug is inserted with
the machine switched on, or if the power supply is
restored following an interruption, the machine
does not start up. Switch the machine off and on
again.
11. Accessories
Use only genuine Metabo accessories.
See page 5.
Use only accessories which fulfil the requirements
and specifications listed in these operating
instructions.
Always use the suitable accessory and the
prescribed guard for the matching guard for
the application. See page 5. (Illustrations are
examples).
Application:
1 = surface grinding
2 = cut-off grinding
3 = drilling of holes
4 = wire brushes
5 = grinding with sanding paper
Accessories:
1.1 = grinding wheel
2.1 = cut-off wheel "metal"
2.2 = cut-off wheel "masonry/concrete"
2.3 = diamond cutting disc "masonry/concrete"
2.4 = dual-purpose diamond cutting discs
(combined grinding and cutting disc)
3.1 = diamond drill bits
4.1 = wheel brush
4.2 = cup brush
5.1 = flap disc
5.2 = backing pad for sanding sheets
prescribed guard:
Type A = cutting guard
Type B = guard for grinding
Other accessories:
(see also www.metabo.com)
A Dust filter
The fine mesh filter prevents coarse particles from
entering the motor housing. Remove regularly and
clean.
B Multiple position bar for side handle
Permits numerous handle positions.
See www.metabo.com or the catalogue for a
complete range of accessories.
12. Repairs
Repairs to electrical tools must ONLY be
carried out by qualified electricians!
A defective mains cable must be replaced only with
a special, original mains cable from Metabo
available from the Metabo service.
Contact your local Metabo representative if you
have Metabo power tools requiring repairs. See
www.metabo.com for addresses.
You can download a list of spare parts from
www.metabo.com.
ENGLISH en
19