DeWalt DCE555 Manual De Instrucciones página 13

• Do not cut material lying on a hard surface. Clearance
behind material to be cut must be allowed for
protruding bit.
• Disconnect battery from tool before making adjustments,
changing bits, or cleaning tool.
• Do not start the tool with bit engaged in the material.
The bit may grab the material.
Cutting a Hole for an Electrical Outlet
(Fig. G)

WARNING: Shut off all live electric circuits to any areas
where cut‑outs will be made.
1. Push any wiring deeply into the outlet box to avoid
damage from the cutting bit.
2. Before hanging the sheet covering the fixture box, mark
the approximate location of the center of the fixture
box on the wall board. Check the cutting bit depth
against the side of the board to be sure it will cut entirely
through the material.
3. Tack the sheet in place with a few fasteners avoiding the
stud holding the fixture box. This allows the wall board to
flex slightly around the protruding fixture box.
4. Turn the cut‑out tool on. Holding the tool firmly with
both hands, plunge the bit straight into the center of the
fixture box.
5. Cut to the right until the bit reaches the inside edge of
the fixture box. Pull the bit out just enough it to clear the
edge of the fixture box. Plunge the bit in again, holding
the bit gently against the outside of the fixture box.
6. Follow the outside of the fixture box and complete the
cut counterclockwise, keeping slight pressure against the
fixture box. This will minimize wandering and give you a
clean, precise cut.
7. Remove the waste and dust from the fixture box. Finish
fastening the sheet of wall board.
MAINTENANCE

WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can cause injury.
Your power tool has been designed to operate over a long
period of time with a minimum of maintenance. Continuous
satisfactory operation depends upon proper tool care and
regular cleaning.
Cleaning

WARNING: Blow dirt and dust out of all air vents with
clean, dry air at least once a week. To minimize the risk
of eye injury, always wear ANSI Z87.1 approved eye
protection when performing this procedure.

WARNING: Never use solvents or other harsh
chemicals for cleaning the non‑metallic parts of the
tool. These chemicals may weaken the plastic materials
used in these parts. Use a cloth dampened only with
water and mild soap. Never let any liquid get inside the
tool; never immerse any part of the tool into a liquid.
Accessories

WARNING: Since accessories, other than those offered
by D WALT, have not been tested with this product,
e
use of such accessories with this product could be
hazardous. To reduce the risk of injury, only D
recommended accessories should be used with
this product.
Recommended accessories for use with your product are
available at extra cost from your local dealer or authorized
service center. If you need assistance in locating any
accessory, please contact D
(1‑800‑433‑9258) or visit our website: www.dewalt.com.
Tool Connect™ Chip (Fig. J)
Optional Accessory

WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can cause injury.
Your tool is Tool Connect™ Chip ready and has a location for
installation of a Tool Connect™ Chip.
Tool Connect™ Chip is an optional application for your
smart device (such as a smart phone or tablet) that connects
the device to utilize the mobile application for inventory
management functions.
Refer to Tool Connect™ Chip Instruction Sheet for
more information.
installing the Tool Connect™ Chip
1. Remove the retaining screws
Connect™ Chip protective cover
2. Remove the protective cover and insert the Tool
Connect™ Chip into the empty pocket
3. Ensure that the Tool Connect™ Chip is flush with the
housing. Secure it with the retaining screws and tighten
the screws.
4. Refer to Tool Connect™ Chip Instruction Sheet for
further instructions.
Accessory/replacement collets
Sold Separately
• 1/8" (3 mm) ‑ DCE55018
• 5/32" (4 mm) ‑ DCE550532
• 1/4" (6 mm) ‑ DCE55014
Repairs
The charger and batteries are not serviceable. There are no
serviceable parts inside the charger or battery pack.

WARNING: To assure product SAFETY and RELIABILITY,
repairs, maintenance and adjustment (including brush
inspection and replacement, when applicable) should
be performed by a D
D WALT authorized service center. Always use identical
e
replacement parts.
English
e
WALT call 1‑800‑4‑D WALT
e e
that hold the Tool
20
into the tool.
19
13 .
WALT factory service center or a
e
WALT
11