Tabla de contenido
inate tough dirt. The machine's shockproof surface
is rough to make it harder to see scratches caused
during use. However, this does not make it easier to
remove tough stains on the surface. It is prohibited to
use steam machines, hoses with running water and
high-pressure cleaners.
6.6.
BATTERIES
PB-Acid batteries
Carry out maintenance operations in accordance with
the manufacturer's instructions and with all the other
instructions provided in this manual.
Exposing the element plates (not completely im-
mersed in the acid solution) will lead to rapid oxida-
tion and irreparably reduce the element's operating
capacities.
An overflowing acid solution may corrode the machine.
Use battery chargers recommended by the manufac-
turer and, in any case, those that are suitable for the
type of battery to be charged.
Always charge batteries in well-ventilated rooms:
there is an explosion risk!
Always charge batteries in well-ventilated rooms,
there is a risk of explosion!
The use of gel or maintenance-free batteries is highly
recommended.
GEL batteries
Carry out maintenance operations in accordance with
the manufacturer's instructions and with all the other
instructions provided in this manual.
Use only those battery chargers recommended by the
manufacturer.
If the batteries are not used, in either case, for an ex-
tended period of time, disconnect them and restore
the charge within the time limits specified for the
type of battery used (generally and as a precaution,
no more than 3 months for Pb-acid/GEL/AGM batter-
ies, 6 months for Li-ion batteries).
The manufacturer accepts no liability for damage to
batteries caused by failure to follow this procedure.
6.7.
THERMAL BREAKERS
The machine is equipped with electric protection
devices on the main operating components to avoid
costly malfunctions.
Thermal breakers are installed to protect the drive
motor wherever foreseen and the brush motor.
When one of these breakers trips automatically, the
disabled function can be reactivated by fully depress-
ing the button of the breaker.
When the thermal breakers trip, especially when the
machine is used during the first few weeks, it might
not be caused by actual machine malfunctions. How-
ever, a specialized technician should check the device
if the relative breaker continues to trip.
6.8.
PERIODIC MAINTENANCE
For all the operations described herein, refer to the in-
structions and detailed warnings in the relative sections.
6.9.
RECOMMENDED SPARE PARTS
You'll always be able to use your machine as effi-
ciently as possible by maintaining a stock of the most
common consumable materials and by scheduling
routine and extraordinary maintenance. Contact your
dealer for a list of these spare parts.
7.
OPERATING CHECKS
7.1.
PROBLEM SOLVING GUIDE
These indications make it easier to understand the
underlying causes of some problems based on spe-
cific type of inconvenience. For the type of corrective
action to take please refer to the specific sections de-
scribed below.
7.1.1. THE MACHINE DOESN'T WORK
The key isn't inserted or correctly turned.
Insert and turn the key to position ON.
The battery connector is disconnected or poorly
attached to the main wiring connector.
Firmly connect the two connectors.
The machine is charging.
Complete the charging operation.
The batteries are discharged.
Charge the batteries.
The main fuse has blown
Replace it
The control board has overheated
Check the situations of use that may have caused
the fault (high slope, etc.) wait 30 min. and try to avoid
the same incorrect uses. If the problem persists, con-
tact the authorised service centre.
7.1.2. THE MACHINE DOESN'T MOVE
The floor slope is too high.
Push manually the machine to the upper floor level.
The thermal protection of the traction motor is tripped.
Stop the machine and rest it for 5 minutes, the push
the thermal breaker button.
The batteries are discharged.
Charge the batteries.
The traction motor was not stopped when the ma-
chine was switched on.
Place the machine on a flat surface, switch off and
on again with the key.
7.1.3. THE BRUSH DON'T ROTATE
The brush motor switch is not selected.
Press the button to activate the brushes.
The brush motor thermal breaker tripped; the
39
Tabla de contenido
