Bosch BRC3600 Instrucciones De Servicio página 13

Example: Four ice-blue bars and one white bar are dis-
played. The state of charge is between 81 % and 90 %.
If capacity is low, both of the lower displays change colour:
Bar Capacity
2 × orange 30 % to 21 %
1 × orange 20 % to 11 %
1 × red 10 % to reserve
1 × red flashing Reserve to empty
If the eBike battery is being charged, the topmost bar on the
battery charge indicator (3) flashes.
Setting the assistance level
You can set how much the eBike drive assists you while ped-
alling on the operating unit using the (8) and (9) buttons.
The assistance level can be changed at any time, even while
cycling, and is displayed in colour.
Level Notes
OFF Motor support is switched off. The eBike can
just be moved by pedalling, as with a normal bi-
cycle.
ECO Effective support with maximum efficiency, for
maximum range
Steady support, long range for touring
TOUR
TOUR+ Dynamic assistance for natural, sporty cycling
eMTB/ Optimal support whatever the terrain, rapid ac-
celeration when starting from a standstill, im-
SPORT
proved dynamics and top performance
TURBO Maximum support even at a high cadence, for
sport cycling
AUTO The support is dynamically adapted to the rid-
ing situation.
RACE Maximum support on the eMTB racetrack; very
direct response and maximum "Extended
Boost" for the best possible performance in
competitive situations
A)
CARGO Steady, powerful support, so as to be able to
safely transport heavy weights
A) The CARGO assistance level can have an additional description.
The designations and configuration of the assistance levels can be
preconfigured by the manufacturer and selected by the bicycle re-
tailer.
Adapting the Assistance Level
The assistance level can be adapted within certain limits us-
ing the eBike Flow app. This gives you the option of adjust-
ing your eBike to your personal requirements.
It is not possible to create a completely new mode. You can
only adjust the modes that have been enabled by the manu-
facturer or dealer on your system. This may be fewer than
4 modes.
Due to technical limitations, you cannot adjust the eMTB
and TOUR+ modes. In addition, restrictions in your country
may mean that it is not possible to adjust a particular mode.
Bosch eBike Systems
The following parameters are available for making adjust-
ments:
– Assistance in relation to the base value of the mode
(within the legal requirements)
– Drive response
– Top limit speed (within the legal requirements)
– Maximum torque (within the limits of the drive)
The parameters are dependent on each other and influence
each other. For example, it is not fundamentally possible to
simultaneously set a low torque value and high assistance.
Note: Please ensure that your modified mode retains the po-
sition, name and colour on all on-board computers and con-
trols.
Interaction between the eBike system and gear-
shifting
The gear shifting should be used with an eBike drive in the
same way as with a normal bicycle (observe the operating in-
structions of your eBike on this point).
Irrespective of the type of gear shifting, it is advisable that
you briefly reduce the pressure on the pedals when changing
gear. This will aid gear shifting and reduce wear on the
powertrain.
By selecting the correct gear, you can increase your speed
and range while applying the same amount of force.
Switching bike lights on/off
Check that your bike lights are working correctly before
every use.
To switch on the bike lights, press the (9) button for more
than 1 s.
You can use the (11) and (10) buttons to control the bright-
ness of the LEDs on the operating unit.
Switching the push assistance on/off
The walk assistance makes it easier to push your eBike. The
speed in this function depends on the selected gear and can
reach a maximum of 4 km/h.
The push assistance function must only be used when
u
pushing the eBike. There is a risk of injury if the wheels
of the eBike are not in contact with the ground while using
the push assistance.
To start walk assistance, press the (8) button for more than
1 s and keep it pressed. The battery charge indicator (3)
goes out and a white moving light in the direction of travel
shows that it is ready.
To activate walk assistance, one of the following actions
must occur within the next 10 s:
– Push the eBike forwards.
– Push the eBike backwards.
– Perform a sideways tilting movement with the eBike.
After activation, the motor begins to push and the continu-
ously filling white bars change colour to ice-blue.
If you release the (8) button, walk assistance is stopped. You
can reactivate walk assistance within 10 s by pressing the
(8) button.
English – 3
0 275 007 3RL | (09.03.2022)