Idiomas disponibles
Idiomas disponibles
en
20
Emission values for vibration
Vibration
Classification according to per-
formance class*
STARLOCK
STARLOCK PLUS
STARLOCK MAX
a
K
* Measured with adapter for SuperCut with QuickIN
3 52 22 952 05 0.
** These values are based on a no-load measurement with
maximum speed stage (6) for STARLOCK and STARLOCK
PLUS and with speed stage (4) for STARLOCK MAX. In each
case, the application tool corresponds to the highest mass iner-
tia of its performance class.
Operating Instructions.
Changing the tool (see page 5)
Do not use accessories not specifically intended and
recommended for this power tool by FEIN. The use of
non-original FEIN accessories can lead to overheating
of the power tool and destroy it.
When changing application tools with sharp cut-
ting edges, use cover to protect yourself against
hand injuries.
Firmly press in the fastening element to the stop.
Then lock the clamping lever.
Protect your hand and fingers against bruising
when locking the clamping lever. The clamping
lever snaps back vigorously by means of spring
force.
Charge-control Indicator on the Battery (see
page 6).
The charge condition can be indicated by the green
LEDs of the charge-control indicator on the battery.
Press the charge-control indicator button
to indicate the charge condition.
When no LED lights up after pressing the charge-con-
trol indicator button, the battery is defective and must
be replaced.
Additional operating instructions.
Guide the power tool toward the work piece only
when switched on.
The self-start prevention lock prevents the power tool
from automatically starting when the battery is inserted
while the on/off switch is set to on.
If the power tool shuts off without the switch being
actuated, switch the power tool switch off, remove the
battery and reattach it.
Before using, sharpen used and even new cutter blades
with the cleaning block.
The symptom for worn blades is a clearly increased
feed force at lower working progress.
The application tool can be offset in 30° steps and fas-
tened in the most favourable working position.
Guide straight, bent or offset cutter blades at a right
angle to the window flange (see page 7-8, Cutter blades
A – D).
For U-shaped cutter blades, pay attention that the
Weighted
traverse of the cutter blade is led parallel to the window
acceleration**
pane of the vehicle (see page 8, Cutter blades E – F).
2
6,3 m/s
The scraper knife is used for cutting back bond remain-
2
6,9 m/s
ders on the window flange or the pane. Before re-
2
bonding the vehicle window, cut back the remaining
8,3 m/s
bead to a height of approx. 2 mm (see page 8, Cutter
2
1,5 m/s
blades G).
Transport.
The contained Li-ion batteries are subject to the Dan-
gerous Goods Legislation requirements. The user can
transport the battery packs by road without further
requirements.
When being transported by third parties (e.g.: air trans-
port or forwarding agency), special requirements on
packaging and labelling must be observed. For prepara-
tion of the item being shipped, consulting an expert for
hazardous material is required.
The recommended Li-ion batteries are subject to the
Dangerous Goods Legislation requirements. The user
can transport the batteries by road without further
requirements.
When being transported by third parties (e.g.: air trans-
port or forwarding agency), special requirements on
packaging and labelling must be observed. For prepara-
tion of the item being shipped, consulting an expert for
hazardous material is required.
Dispatch batteries only when the housing is undam-
aged. Tape or mask off open contacts and pack up the
battery in such a manner that it cannot move around in
the packaging. Please also observe possibly more
detailed national regulations.
Repair and customer service.
or
electricians, as improper maintenance can result in con-
siderable hazards for the user.
tool. Blow out the interior of the power tool via the
ventilation slots frequently with dry and oil-free com-
pressed air.
When working gypsum-containing materials, dust can
settle within the power tool and switch element, which
can harden in connection with humidity. This can
impair the switching mechanism. Blow out the interior
of the power tool via the ventilation slots and the
switch element frequently with dry and oil-free com-
pressed air.
For storage of the power tool, remove the application
tool, shut the clamping lever, and then press in the fas-
tening element.
Products that have come into contact with asbestos
may not be sent in for repair. Dispose of products con-
taminated with asbestos according to the applicable
country-specific regulations for such disposal.
Please observe that power tools may only be
repaired, maintained and inspected by qualified
When working metal under extreme oper-
ating conditions, it is possible for conductive
dust to settle in the interior of the power
