Specific Safety Rules - Urrea TB812 Manual De Usuario

• Use safety equipment. Always wear eye pro-
tection. Dust mask, nonskid safety shoes, hard
hat, or hearing protection must be used for ap-
propriate conditions.
• Before connecting the tool to a power source
(receptacle, outlet, etc.) be sure that the volt-
age supplied is the same as that one specified
on the nameplate of the tool. To use a not
specified voltage may cause a serious injury to
the user as well as damage the tool.
TOOL USE AND CARE
• Do not force the power tool. Use the correct
tool for the application. The correct tool will
do the job better and more safely at the rate
that it was designed to work at.
• Use clamps or other practical way to secure
and support the workpiece to a estable plat-
form. Holding the work by hand or against
your body is unestable and may cause loss of
control.
• Do not use tools if switch does not turn it
on or off. Any tool that cannot be controlled
whith the switch is dangerous and must be re-
paired.
• Disconnect the plug from the power source
before making any adjustments, changing ac-
cessories or storing the tool. This preventive
safety measures reduce the risk of accidental
starting of the tool.
• When the power tool is not in use, store it
out of the reach of children, and do not al-
low individuals who are not familiar with the
power tool or these instructions to operate it.
Power tools are dangerous in the hands on un-
trained users.
• Maintain the power tool. Check for misalign-
ment or binding of moving parts, broken parts,
and any other condition that may affect the
operation of the power tool. If it is damaged,
have it repaired before using. Many accidents
are caused by poorly maintained power tools.
• Check for misalignment or bonding of mov-
ing parts, breakage parts, and any other condi-
tion that may affect the tools operation. If you
find a damaged tool, take it to service before
use it.
• Use only accessories that are recommended
by the manufacturer of your model. Suitable
accessories for one tool, may become hazard-
ous when are used on another tool.
E N G L I S H •
• Do not alter or misuse the tool. These tools
have been built by precision. Any alteration or
modification not specified is misuse and may
result in a dangerous condition.
• Is recommendable to use a safety device suit-
able, such a thermal and diferential switch
when you are using an electric equipment.
REPAIR AND SERVICE
• Tool service must be perfomed only by quali-
fied repair personnel. Service or maintenance
performed by unqualified personnel could re-
sult in a risk of injury.
• When tool service is required, use only identi-
cal replacement parts and follow the instruc-
tions from Maintenance Section in this manual.
The use of unauthorized parts or failure to fol-
low Maintenance Instructions may cause a risk
of electric shock or injury.

SPECIFIC SAFETY RULES

• Only connect the machine to an earthed
mains supply. Only use tree-core extension
cords.
• Always wear safety goggles and a hairnet for
long hair.
• Do not wear gloves, ties or loose clothing.
• While drilling, never hold the workpiece by
hand, but firmly tighten it to the drilling table
using a vice e.g. Never keep your fingers on a
place where they could touch the drill in case
the workpiece should move unexpectedly.
• Do not use the machine until it has been
mounted and installed completely according
to the instructions.
• Do not switch on the machine while mov-
ing the head relative to the table or viceversa.
Do not switch on the machine until having
checked that head and table have been tight-
ened firmly to the pillar.
• Do not use the machine if any part is dam-
aged or badly functioning.
• Adjust the table or depth stop to prevent the
drill from entering the table. Do not perform
any design, assembly or construction activities
on the table while the machine is switched on.
• Make sure that the chuck key (if applicable)
has been removed before switching on the ma-
chine.
U s e r's m a nu al
9