Trevi MCX 1021 USB Manual De Uso Y Conexiones página 7

ENGLISH
INSTALLATION AND CONNECTION
Connect the RCA plug of the speakers cable to the output socket of the right (16) and left (17) speaker.
Plug the FM antenna into the FM antenna input socket (15).
POWER SUPPLY
CONNECTING TO THE MAINS SUPPLY
Fit the plug into an AC 230V - 50Hz socket. Do not plug the appliance to different power.
Unless otherwise specified, the controls description applies to both the appliance and the remote control.
ON/OFF SWITCHING
1. Press the main ON/OFF key (13).
2. Press the main ON/OFF key again to switch the appliance off.
STANDBY
1. When the appliance is on, press the POWER key (1) of the remote control to activate the standby function.
2. Press the POWER key (1) again to resume the appliance from the standby mode.
VOLUME CONTROL AND MUTE FUNCTION
It is possible to control the volume from the appliance by using the volume control (3) or from the remote control with the VOL+
(20) e VOL- (19) keys, with a range of 0 to 36. While adjusting the volume, the display will show the level of the selected volume.
MUTE function: it is possible to activate the audio off function with the MUTE key (1) or with the MUTE key (3) on the remote
control. To switch the audio on, press the MUTE key again.
RADIO FUNCTION
1. Switch the appliance on and press the FUNCTION key (5) on the appliance or the MODE key (12) on the remote control until
the FM icon is displayed.
2. In order to tune and store automatically, use the
The appliance will automatically scan all the available radio stations and will store up to a maximum of 30 stations; in order
to recall the stored stations, press the CH+ (10) or CH- (9) keys.
3. Adjust the volume using the VOLUME control (3) or using the VOL+ (20) and VOL- (19) keys on the remote control.
4. In order to perform a manual search, use the SCAN+ (8) and SCAN- (7) keys, holding them will cause the appliance to tune
on the first strong signal, pressing them once will allow you to perform a step by step tuning, with frequency variations of 0.10MHz.
You can perform the same actions by using the SEEK+ (15) and SEEK- (5) keys on the remote control.
You can save the radio station by using the SAVE key (18):
5. Press the SAVE key (18). A number will start blinking on the display.
6. With the CH+ (4) and CH- (16) keys on the remote control, select the memory number that you want to use to store the station.
7. Press the SAVE key (18) again.
NOTES
To obtain the best reception in FM, extend and orient the antenna. If the reception is bad, try adjusting the length and orientation
of the antenna. However, the reception quality depends very much on where the appliance is placed.
USB/SD CARD READER OPERATION
PLAYBACK
1. Make sure that an SD memory card is inserted in the SD/MMC slot (4) or a USB device is inserted in the USB port (6).
2. Switch the appliance on and press the FUNCTION key (5) on the appliance or the MODE key (12) on the remote control until
the CARD icon is displayed if you want to read the SD card or the USB icon if you want to read from a USB device.
3. After a few seconds the reader will automatically start playing the detected audio tracks (MP3 or WMA).
4. Press the / key (11) to pause.
5. To disable the pause, press once again the
6. To stop playback using the remote control, press the
DIRECT TRACK SELECTION
In order to directly select a track, use the numeric keypad of the remote control (2):
1. Press the number of the desired track.
2. The reader will automatically play the selected track.
All manuals and user guides at all-guides.com
/ (11) key on the appliance or the AUTO key (9) on the remote control.
/ key (11).
STOP key (8).
7
MCX 1021 USB