Mounting Bracket Installation; Troubleshooting Guide; Need Help - Good Earth Lighting UC1306-WH1-09LFC-G Manual De Instrucciones

Tabla de contenido

Idiomas disponibles

AAx2

BBx2

Mark the general area where the mounting bracket (AA) will be located. Using a small drill or nail, make two small pilot holes at the marked locations. Align the

mounting brackets (AA) and drive screws (BB) into place. NOTE: Ensure mounting location is within 5ft. of an electrical outlet.

Lift the fixture toward the mounting brackets (AA) while aligning the top of the fixture channel with both clips. Apply upward pressure until channel snaps into

place and seats into both brackets.

Connect fixtures, wave/5CCT sensor switch, and plug-in driver by using the provided various sizes of linking cords. Use provided cord clips where additional

wire control is needed. Peel the backing off each clip and mount where required. Plug the Plug-in Driver into the outlet.

PLANNING: OPTIONAL LAYOUTS AND CONNECTING

Up to 30 in

CARE AND MAINTENANCE:

Periodically clean the fixture and diffuser using a mild, non-abrasive cleaner and soft cloth. When cleaning the fixture, make sure the power is turned off. Do not spray cleaner directly onto

any part of the fixture or LEDs.

Good Earth Lighting

- 6 YEAR LIMITED WARRANTY:

The manufacturer warrants this lighting fixture to be free from defects in materials and workmanship for a period of (6) years from the date of original purchase by the consumer. The

fixture is not warrantied for use in a commercial or retail application. The warranty is limited to use in a residential environment. We will repair or replace (at our option) the unit in the

original color and style if available, or in a similar color and style if the original item has been discontinued, without charge. Defective units must be properly packed and returned to the

manufacturer with a letter of explanation and your original purchase receipt showing date of purchase. Call 1-800-291-8838 to obtain a return authorization number and an address

where to ship your defective product. Note: C.O.D. shipments will NOT be accepted. The liability of the manufacturer is in any case limited to replacement of the defective light fixture

product. The manufacturer will not be liable for any other loss, damage, labor costs or injury which is caused by the product. This limitation upon the liability of the manufacturer includes

any loss, damage, labor costs or injury which is (I) to person or property or otherwise; (II) incidental or consequential in nature; (III) based upon theories of warranty, contract, negligence,

strict liability, tort, or otherwise; or (IV) directly, or indirectly related to the sale, use, or repair of the product. This warranty gives you specific rights, and you may also have other rights

which vary from state to state.

FCC STATEMENT:

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation. Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority

to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no guarantee that the interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: 1)

Reorient or relocate the receiving antenna. 2) Increase the separation between the equipment and receiver. 3) Connect the equipment into an outlet on a circuit different from that of the receiver. 4) Consult the

dealer or an experienced radio/TV technician for help.

FCC responsible party name : Good Earth Lighting, Inc. Address: 1400 E Business Center Drive, STE 108, Mount Prospect IL 60056, USA

Telephone number: 1-800-291-8838

PROBLEM

1. Light does not come on.

2. Fuse blows or circuit breaker trips when

light is turned on.

REPLACEMENT PARTS LIST