Makita AN911H Manual De Instrucciones página 3

Clavadora para construcción
Ocultar thumbs Ver también para AN911H:
Tabla de contenido
Idiomas disponibles

Idiomas disponibles

disconnected, altered, or not working properly.
12. Operate the tool within the specified air
pressure on the tool label for safety and
longer
tool
life.
recommended max. operating pressure. The
tool should not be connected to a source
whose pressure potentially exceeds 480 PSIG
(3.39 MPa).
13. Never
use
the
compressed air. If bottled gas (carbon dioxide,
oxygen, nitrogen, hydrogen, air, etc.) or
combustible
acetylene, etc.) is used as a power source for
this tool, the tool will explode and cause
serious injury.
14. Always check the tool for its overall condition
and loose screws before operation. Tighten as
required.
15. Make sure all safety systems are in working
order before operation. The tool must not
operate if only the trigger is pulled or if only
the contact element is pressed against the
wood. It must work only when both actions
are
performed.
operation with nails unloaded and the contact
element in fully pulled position.
16. Check walls, ceilings, floors, roofing and the
like carefully to avoid possible electrical
shock, gas leakage, explosions, etc. caused
by striking live wires, conduits or gas pipes.
17. Use only nails specified in this manual. The
use of any other nails may cause malfunction
of the tool.
18. Do not permit those uninstructed to use the
tool.
19. Make sure no one is nearby before nailing.
Never attempt to nail from both the inside and
outside at the same time. Nails may rip
through and/or fly off, presenting a grave
danger.
20. Watch your footing and maintain your balance
with the tool. Make sure there is no one below
when working in high locations, and secure
the air hose to prevent danger if there is
sudden jerking or catching.
21. On rooftops and other high locations, nail as
you move forward. It is easy to lose your
footing if you nail while inching backward.
When nailing against perpendicular surface,
nail from the top to the bottom. You can
perform nailing operations with less fatigue
by doing so.
22. A nail will be bent or the tool can become
jammed if you mistakenly nail on top of
another nail or strike a knot in the wood. The
Do
not
exceed
tool
with
other
gas
(hydrogen,
Test
for
possible
nail may be thrown and hit someone, or the
tool itself can react dangerously. Place the
nails with care.
the
23. Do not leave the loaded tool or the air
compressor under pressure for a long time
out in the sun. Be sure that dust, sand, chips
and foreign matter will not enter the tool in the
place where you leave it setting.
than
24. Do not point the ejection port at anyone in the
vicinity. Keep hands and feet away from the
ejection port area.
propane,
25. When the air hose is connected, do not carry
the tool with your finger on the trigger or hand
it to someone in this condition. Accidental
firing can be extremely dangerous.
26. Handle the tool carefully, as there is high
pressure
dangerous if a crack is caused by rough
handling (dropping or striking). Do not
attempt to carve or engrave on the tool.
27. Stop nailing operations immediately if you
notice something wrong or out of the ordinary
with the tool.
faulty
28. Always disconnect the air hose and remove
all of the nails:
29. Perform cleaning and maintenance right after
finishing the job. Keep the tool in tip-top
condition. Lubricate moving parts to prevent
rusting and minimize friction-related wear.
Wipe off all dust from the parts.
30. Do not modify tool without authorization from
Makita.
31. Do not attempt to keep the trigger or contact
element depressed with tape or wire. Death or
serious injury may occur.
32. Always check contact element as instructed
in
accidentally if the safety mechanism is not
working correctly.
33. Ask Makita's Authorized service centers for
periodical inspection of the tool.
34. To
RELIABILITY, maintenance and repairs should
be performed by Makita Authorized or Factory
Service
replacement parts.
SAVE THESE INSTRUCTIONS.
3
inside
the
When unattended.
Before performing any maintenance or
repair.
Before cleaning a jam.
Before moving the tool to a new location.
this
manual.
Nails
maintain
product
Centers,
always
tool
that
can
be
may
be
driven
SAFETY
and
using
Makita
Tabla de contenido
loading

Tabla de contenido