Tabla de contenido
Idiomas disponibles
Idiomas disponibles
W
Watts
min
minutes
Alternating
Current
Position of Date Code (FIG. B)
The Date Code, which also includes the year of manufacture,
is printed into the housing.
Example:
2018 XX JN
Year of manufacturing
PACKAGE CONTENTS
The package contains:
1 Polisher
1 Velcro backing pad
1 Velcro wool bonnet
1 Instruction manual
1 Warranty card
1 Service center list
♦ Check for damage to the tool, parts or accessories
which may have occurred during transport.
♦ Take the time to thoroughly read and understand this
manual prior to operation.
ELECTRICAL SAFETY
Your tool is double insulated; therefore no earth wire
is required. Always check that the main voltage
corresponds to the voltage on the rating plate.
Warning! If the power cord is damaged, it must be
replaced by the manufacturer, authorized Stanley
Service Center or an equally qualified person in
order to avoid damage or injury. If the power cord is replaced
by an equally qualified person, but not authorized by
Stanley the warranty will not be valid.
USING AN EXTENSION CABLE
If it is necessary to use an extension cable, please used
an approved extension cable that fits the tool's power input
specifications. The minimum cross-sectional area of the
conducting wire is 1.5 sq. mm. Cables should be untangled
before reeling up.
Cable cross-sectional
area (mm
)
2
0.75
1.00
1.50
2.50
4.00
Earthing Terminal
Safety Alert Symbol
Revolutions or
/min.
Reciprocation per
minute
Cable rated current
(Ampere)
6
10
15
20
25
Cable length (m)
Voltage
Amperes Cable rated current (Ampere)
115
0 - 2.0
2.1 - 3.4
3.5 - 5.0
5.1 - 7.0
7.1 - 12.0
12.1 - 20.0
230
0 - 2.0
2.1 - 3.4
3.5 - 5.0
5.1 - 7.0
7.1 - 12.0
12.1 - 20.0
FEATURES
This tool includes some or all of the following features.
1. Speed control wheel
2. Velcro backing pad
3. Trigger switch
4. Brush cap
5. Spindle lock button
6. Lock-on button
7. D-handle
8. Velcro bonnet
9. Spindle
ASSEMBLY
WARNING! Before assembly, make sure that the
tool is switched off and unplugged.
WARNING! To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories. Before reconnecting
the tool, depress and release the trigger switch to ensure
that the tool is off. An accidental start-up can cause injury.
Speed Control Wheel (Fig. A)
The maximum speed of your tool can be changed by
rotating the speed control wheel (1) to the desired setting.
The wheel incorporates detents to prevent inadvertent
wheel movement and to facilitate speed selection. For
added versatility, the switch may be locked in its full on
position and tool speed changed by means of the speed
control wheel (1) alone.
The electronic speed control not only lets you select
the speed to suit the job, but also helps to maintain that
consistent speed as you load the tool by pressing down.
The speed control wheel (1) can be set for any speed
between 500 and 3600 RPM from level 1 to level MAX.
7.5
15
25
30
45
6
6
6
6
6
6
6
6
6
15
6
6
10
15
20
10
10
15
20
20
15
15
20
25
25
20
20
25
-
-
6
6
6
6
6
6
6
6
6
6
6
6
6
6
10
10
10
10
10
15
15
15
15
15
20
20
20
20
20
25
60
10
15
20
25
-
-
6
6
15
15
20
-
21
Tabla de contenido
