Mitsubishi Electric Mr.SLIM SLZ-M FA Serie Manual De Instrucciones página 16

7. Trouble Shooting
Air conditioner does not heat or cool well.
When heating operation starts, warm air does not blow from the indoor
unit soon.
During heating mode, the air conditioner stops before the set room tem-
perature is reached.
During cooling mode, the air conditioner stops when the set room tem-
perature is reached.
Airflow direction changes during operation or airflow direction cannot be set.
When the airflow direction is changed, the vanes always move up and down
past the set position before finally stopping at the position.
A flowing water sound or occasional hissing sound is heard.
A cracking or creaking sound is heard.
en
The room has an unpleasant odor.
A white mist or vapor is emitted from the indoor unit.
Water or vapor is emitted from the outdoor unit.
" " appears in the remote controller display.
When restarting the air conditioner soon after stopping it, it does not oper-
ate even though the ON/OFF button is pressed.
Air conditioner operates without the ON/OFF button being pressed.
Air conditioner stops without the ON/OFF button being pressed.
Remote controller timer operation cannot be set.
"Please Wait" appears in the remote controller display.
An error code appears in the remote controller display.
Draining water or motor rotation sound is heard.
The vanes do not move or the indoor unit does not respond to input from
the wireless remote controller.
14
Having trouble? Here is the solution. (Unit is operating normally.)
I Clean the filter. (Airflow is reduced when the filter is dirty or clogged.)
I Check the temperature adjustment and adjust the set temperature.
I Make sure that there is plenty of space around the outdoor unit. Is the
indoor unit air intake or outlet blocked?
I Has a door or window been left open?
I Warm air does not blow until the indoor unit has sufficiently warmed up.
I When the outdoor temperature is low and the humidity is high, frost
may form on the outdoor unit. If this occurs, the outdoor unit performs a
defrosting operation. Normal operation should begin after approximately
10 minutes.
I For SLZ-M·FA series, when the set room temperature is reached during
cooling mode, the fan operates at the lowest speed.
I During heating mode, the vanes automatically move to the horizontal
airflow direction when the airflow temperature is low or during defrosting
mode.
I When the airflow direction is changed, the vanes move to the set position
after detecting the base position.
I These sounds can be heard when refrigerant is flowing in the air condi-
tioner or when the refrigerant flow is changing.
I These sounds can be heard when parts rub against each due to expan-
sion and contraction from temperature changes.
I The indoor unit draws in air that contains gases produced from the walls,
carpeting, and furniture as well as odors trapped in clothing, and then
blows this air back into the room.
I If the indoor temperature and the humidity are high, this condition may
occur when operation starts.
I During defrosting mode, cool airflow may blow down and appear like a
mist.
I During cooling mode, water may form and drip from the cool pipes and
joints.
I During heating mode, water may form and drip from the heat exchanger.
I During defrosting mode, water on the heat exchanger evaporates and
water vapor may be emitted.
I During central control, " " appears in the remote controller display and
air conditioner operation cannot be started or stopped using the remote
controller.
I Wait approximately three minutes.
(Operation has stopped to protect the air conditioner.)
I Is the on timer set?
Press the ON/OFF button to stop operation.
I Is the air conditioner connected to a central remote controller?
Consult the concerned people who control the air conditioner.
I Does " " appear in the remote controller display?
Consult the concerned people who control the air conditioner.
I Has the auto recovery feature from power failures been set?
Press the ON/OFF button to stop operation.
I Is the off timer set?
Press the ON/OFF button to restart operation.
I Is the air conditioner connected to a central remote controller?
Consult the concerned people who control the air conditioner.
I Does " " appear in the remote controller display?
Consult the concerned people who control the air conditioner.
I Are timer settings invalid?
If the timer can be set, or
I The initial settings are being performed. Wait approximately 3 minutes.
I The protection devices have operated to protect the air conditioner.
I Do not attempt to repair this equipment by yourself.
Turn off the power switch immediately and consult your dealer. Be sure
to provide the dealer with the model name and information that appeared
in the remote controller display.
I When cooling operation stops, the drain pump operates and then stops.
Wait approximately 3 minutes.
I The junction wire connectors of the vane motor and signal receiver may
not be connected correctly. Have an installer check the connections. (The
colors of the male and female sections of the junction wire connectors
must match.)
appears in the remote controller display.