Tabla de contenido
Idiomas disponibles
Idiomas disponibles
2.
Never service damaged battery packs. Service
of battery packs should only be performed by the
manufacturer or authorized service providers.
3.
Follow instruction for lubricating and chang-
ing accessories.
4.
Do not modify or attempt to repair the appli-
ance or the battery pack except as indicated in
the instructions for use and care.
Cordless Chain saw safety warnings
1.
Keep all parts of the body away from the saw
chain when the chain saw is operating. Before
you start the chain saw, make sure the saw
chain is not contacting anything. A moment of
inattention while operating chain saws may cause
entanglement of your clothing or body with the
saw chain.
2.
Always hold the chain saw with your right
hand on the rear handle and your left hand on
the front handle. Holding the chain saw with a
3.
Hold the power tool by insulated gripping
surfaces only, because the saw chain may con-
tact hidden wiring.
wire may make exposed metal parts of the power
shock.
4.
Wear safety glasses and hearing protection.
Further protective equipment for head, hands,
legs and feet is recommended. Adequate protec-
debris or accidental contact with the saw chain.
5.
Do not operate a chain saw in a tree. Operation
of a chain saw while up in a tree may result in
6.
Always keep proper footing and operate the
and level surface. Slippery or unstable surfaces
such as ladders may cause a loss of balance or
control of the chain saw.
7.
When cutting a limb that is under tension be
alert for spring back. When the tension in the
strike the operator and/or throw the chain saw out
of control.
8.
Use extreme caution when cutting brush and
saplings.
chain and be whipped toward you or pull you off
balance.
9.
Carry the chain saw by the front handle with
the chain saw switched off and away from your
body. When transporting or storing the chain
handling of the chain saw will reduce the likelihood
of accidental contact with the moving saw chain.
10. Follow instructions for lubricating, chain ten-
sioning and changing accessories. Improperly
tensioned or lubricated chain may either break or
increase the chance for kickback.
11.
Keep handles dry, clean, and free from oil and
grease. Greasy, oily handles are slippery causing
loss of control.
12. Cut wood only. Do not use chain saw for pur-
poses not intended. For example: do not use
chain saw for cutting plastic, masonry or non-
wood building materials. Use of the chain saw
for operations different than intended could result
in a hazardous situation.
13. Causes and operator prevention of kickback:
Kickback may occur when the nose or tip of the
closes in and pinches the saw chain in the cut.
reverse reaction, kicking the guide bar up and
back towards the operator. Pinching the saw chain
along the top of the guide bar may push the guide
bar rapidly back towards the operator. Either of
these reactions may cause you to lose control of
the saw which could result in serious personal
devices built into your saw. As a chain saw user,
you should take several steps to keep your cutting
Kickback is the result of tool misuse and/or incor-
rect operating procedures or conditions and can
be avoided by taking proper precautions as given
below:
Proper
14. Before starting work, check that the chain
saw is in proper working order and that its
condition complies with the safety regulations.
Check in particular that:
5 ENGLISH
with both hands on the saw and position
your body and arm to allow you to resist
kickback forces. Kickback forces can be
controlled by the operator, if proper precau-
tions are taken. Do not let go of the chain
saw.
Do not overreach and do not cut above
shoulder height.
tended tip contact and enables better control
of the chain saw in unexpected situations.
Only use replacement bars and chains
replacement bars and chains may cause
chain breakage and/or kickback.
Follow the manufacturer's sharpening
and maintenance instructions for the saw
chain. Decreasing the depth gauge height
can lead to increased kickback.
-
Incorrect
Tabla de contenido
