Idiomas disponibles
Idiomas disponibles
SAFETY INSTRUCTIONS FOR ANGLE GRINDERS
GENERAL
Only use this tool for dry grinding/cutting
●
Only use the flanges which are supplied with this tool
●
This tool should not be used by people under the age of
●
16 years
Always disconnect plug from power source before
●
making any adjustment or changing any accessory
ACCESSORIES
Use the original SKIL accessories which can be obtained
●
from your SKIL dealer
For mounting/using non-SKIL accessories observe the
●
instructions of the manufacturer concerned
Use only accessories with an allowable speed matching
●
at least the highest no-load speed of the tool
Do not use damaged, deformed or vibrating grinding/
●
cutting discs
Handle and store grinding/cutting discs carefully to avoid
●
chipping and cracking
Protect accessories from impact, shock and grease
●
Do not use a grinding/cutting disc that is larger than the
●
maximum recommended size
Only use grinding/cutting discs with a hole diameter
●
which fits mounting flange G 2 without play; never use
reducors or adaptors to fit large-hole grinding/cutting
discs
Never use grinding/cutting discs with a threaded hole, of
●
which the thread is not long enough to accept the spindle
length of the tool
Never use accessories with a "blind" threaded hole
●
smaller than M14 x 21 mm
OUTDOOR USE
Connect the tool via a fault current (FI) circuit breaker
●
with a triggering current of 30 mA maximum
Only use an extension cord which is intended for outdour
●
use and equipped with a splashproof coupling-socket
BEFORE USE
Before using the tool for the first time, it is recommended
●
to receive practical information
Do not work materials containing asbestos (asbestos
●
is considered carcinogenic)
Take protective measures when during work dust
●
can develop that is harmful to one's health,
combustible or explosive (some dusts are considered
carcinogenic); wear a dust mask and work with dust/chip
extraction when connectable
Be careful of hidden electrical wires or gas- and water
●
pipes; check the work area, for instance with a metal
detector
Be careful when cutting grooves, especially in supporting
●
walls (slots in supporting walls are subject to country-
specific regulations; these regulations are to be observed
under all circumstances)
Clamp the workpiece in case it does not remain
●
stationary from its own weight
Do not clamp the tool in a vice
●
Use completely unrolled and safe extension cords with a
●
capacity of 16 Amps (UK 13 Amps)
Wear protective glasses and gloves, hearing
●
protection 4 and sturdy shoes; when necessary, also
wear an apron
Always mount auxiliary handle E 2 and protective guard
●
F 2; never use the tool without them
Be sure tool is switched off when plugging in
●
DURING USE
Always keep the cord away from moving parts of the
●
tool; direct the cord to the rear, away from the tool
If the cord is damaged or cut through while working, do
●
not touch the cord, but immediately disconnect the plug;
never use the tool with a damaged cord
Push spindle-lock button D 2 only when spindle A 2 is
●
at a standstill
Keep hands away from rotating accessories
●
When grinding metal, sparks are generated; keep other
●
persons and combustible material from work area
In case of electrical or mechanical malfunction,
●
immediately switch off the tool and disconnect the plug
In case the cutting disc is blocked, resulting in jerking
●
forces on the tool, immediately switch off the tool
In case of current interruption or when the plug is
●
accidentally pulled out, unlock the on/off switch H 2
immediately and put it in the OFF-position in order to
prevent uncontrolled restarting
Do not apply so much pressure on the tool that it comes
●
to a standstill
AFTER USE
Before you put down the tool, switch off the motor and
●
ensure that all moving parts have come to a complete
standstill
After switching off the tool, never stop the rotation of the
●
accessory by a lateral force applied against it
WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):
Do not connect the blue (= neutral) or brown (= live) wire
●
in the cord of this tool to the earth terminal of the plug
If for any reason the old plug is cut off the cord of this
●
tool, it must be disposed of safely and not left unattended
TOOL ELEMENTS 2
A Spindle
B Clamping flange
C Spanner
D Spindle-lock button
E Auxiliary handle
F Safety guard
G Mounting flange
H On/off locking switch
J Grip ring
K Speed selection wheel (9470)
L Ventilation slots
USE
Mounting of accessories 2 5
●
! disconnect the plug
- clean spindle A and all parts to be mounted
- tighten clamping flange B with spanner C while
pushing spindle-lock button D
- for removing accessories handle vice-versa
8
