Deleting Scenes; Programs (Chase); Creating / Extending Programs; Calling Up Programs - IMG STAGELINE DMX-3216 Manual De Instrucciones

Repeat steps 2 to 4 to call up additional scenes.
GB
Combining scenes by means of the buttons (1) will
always provide the higher value of a channel. Fad-
ing in scenes by means of the sliders will always
apply the most recent value (i. e. the value of the
scene whose slider has most recently been
moved), with the exception of the channels for
which the value zero has been saved.
Important: DMX channels that were directly con-
trolled before a scene is called up (
will retain their previously set values and will not
adopt the value of the scene being called up. If this
is not desired, press the button RELEASE / CLEAR
(23) to reset all channels prior to calling up a scene.

5.2.3 Deleting scenes

1) Keep the button PROGRAM / REC (10) pressed
for 3 s. The LED next to the button will start to
flash to indicate that the programming mode has
been activated.
2) Press the button SCENE / FIXTURE (5) so that
the LED above the button starts to flash.
3) Select the level to which the scene to be deleted
is saved. The LEDs A – D (2) indicate the current
level. Use the button PAGE (3) to switch to
another level.
LEDs light up above the buttons to which a
scene has been saved.
4) To delete the scene, keep the button DEL (21)
pressed and also press the button for the scene
to be deleted. All LEDs will flash briefly to con-
firm the deletion; the LED above the button will
extinguish.
Repeat steps 3 and 4 to delete further scenes.
5) To exit the programming mode, keep the button
PROGRAM / REC (10) pressed for 3 s. The LED
next to the button will extinguish.

5.3 Programs (CHASE)

Unlike scenes that must be called up manually and
individually, programs are made up of a sequence
of adjustments that can be called up automatically
(using adjustable intervals), music-controlled or
manually. 16 programs with up to 750 steps may be
saved. The programs may run at the same time.

5.3.1 Creating / extending programs

1) Keep the button PROGRAM / REC (10) pressed
for 3 s. The LED next to the button will start to
flash to indicate that the programming mode has
been activated.
2) Press the button CHASE (7). The LED above
the button will light up. In addition, the LEDs
22
3) Press one of the 16 number buttons to which the
chapter 5.1)
4) Consecutively select and adjust the units to be
5) Press the button PROGRAM / REC briefly. The
6) To exit the programming mode, keep the button

5.3.2 Calling up programs

1) Press the button CHASE (7). The LED above
2) Use the number buttons (17) to call up the pro-
3) The LEDs AUTO, MUSIC and MANUAL (8) indi-
above the number buttons (17) to which a pro-
gram has already been saved will start to flash.
new program is to be saved. Selecting a number
button to which a program has already been
saved will add additional program steps to the
existing program. All the LEDs above the num-
ber buttons will extinguish after a short period of
time; the LED above the button SCENE / FIX-
TURE (5) will light up instead of the LED above
the button CHASE. In addition,
appear on the display.
used by the program (
up scenes that have already been created
( chapter 5.2.2).
program step will be saved. All LEDs will briefly
flash to confirm that the program step has been
saved; the following will appear on the display:
Chase xx
STEP 001
(program xx, program step 1)
Repeat steps 4 and 5 to add further steps to the
program.
Repeat steps 2 to 5 to create further programs.
PROGRAM / REC pressed for 3 s. The LED next
to the button will extinguish.
the button will light up;
display.
gram. The LED above the button will light up; the
following will now appear on the display:
Chase xx
STEP 001
(program xx, current program step 1)
It is also possible to select multiple programs at
the same time. The display will then refer to the
program most recently selected.
When a button is pressed to which no pro-
gram has been saved,
display.
cate the control type currently selected for the
programs. Use the button next to the LEDs to
switch over between the types:
AUTO
The program will be time-controlled. Use the
control FADE TIME (25) to adjust the crossfade
FIXTURE
chapter 5.1) or call
Chase will appear on the
NULL will appear on the
will