How To Replace Grease; Maintenance And Inspection - Hitachi DH 40YB Instrucciones De Manejo

1. When an anchor adapter is used.
(1) Turn the selector lever to the striking position ( ).
(Fig. 8)
(2) Install the self-drilling anchor in the rotation-striking
anchor adapter. (Fig. 11)
(3) Turn the power on and determine the self-drilling
anchor position.
(4) Turn the power off, set the selector lever to rotation-
striking position (
prepare hole with self-drilling anchor.
(5) When the specified depth is obtained, pull out the
anchor. (Fig. 12)
(6) Employ the syringe to blow out chip.
(7) Attach the plug to the anchor tip, set the selector
lever to striking position ( ) and drive in the anchor.
(8) After driving in the anchor, use the drift key to
separate the anchor. (Fig. 13)
(9) By employing a manual hammer or pliers, snap off
the tapered portion of the anchor. (Fig. 14)
CAUTION
Since the snapped-off tapered portion will fly out,
pay attention to the snapping direction.
2. When a taper shank adapter is used. (Fig. 15)
(1) Install drill bit with taper shank in the taper shank
adapter.
(2) Turn the power on and drill a base hole to the depth
sounded by indicating groove on the drill bit.
(3) After cleaning out dust with a syringe, attach the
plug to the anchor tip and drive in the anchor with
a manual hammer.
(4) To remove the drill bit (taper shank), insert the
cotter into the slot of the taper shank adapter and
strike the head of the cotter with a hammer
supporting on a rest. (Fig. 16)
HOW TO HANDLE A CORE BIT
When a core bit is used, large caliber holes and blind
holes can be drilled. In this case, use optional accessories
for core bits (such as a center pin and core bit shank) for
more rational operation.
1. Mounting
CAUTION
Prior to mounting a core bit, always disconnect the
plug from the power supply receptacle.
(1) Mount the core bit on the core bit shank. (Fig. 17)
Before that, feed oil to the screw portion of core
bit shank for easy dismount.
(2) Mount the core bit shank on the drill main body
in the same manner as in mounting the drill bit
and the bull point. (Fig. 18)
(3) Insert the center pin into the guide plate until it
reaches the extremity.
(4) Fit in the guide plate by aligning its concaved
portion with the core bit tip. When the position of
the concave is shifted by turning the guide plate
right or left, the guide plate never slips off even
when the drill is used in a downward direction.
(Fig. 19)
2. Drilling holes
(1) Insert the plug into a power supply receptacle.
(2) A spring is built in the center pin. By straightly and
gently pressing it to the wall or floor surface, the
entire surface of the core bit tip attains contact to
start the hole drilling job. (Fig. 20)
), turn the power on again and
(3) When the hole depth reaches approximately 5 mm,
the hole position can be determined. Then remove
the center pin and guide plate from the core bit
and continue the hole drilling job.
CAUTION
When removing the center pin and guide plate,
always disconnect the plug from the power supply
receptacle.
3. How to dismount the core bit (Fig. 21)
(1) By holding the drill (with the core bit inserted) in
an upward position, drive the drill to repeat impact
operation two or three times, whereby the screw
is loosened and the drill becomes ready for
disassembly.
(2) Remove the core bit shank from the drill, hold the
core bit with one hand, and strongly strike the head
of the hexagonal portion of the core bit shank with
a hand hammer two or three times, whereby the
round head screw is loosened and the drill is ready
for disassembly. (Fig. 22)

HOW TO REPLACE GREASE

This machine is of full air-tight construction to protect
against dust and to prevent lubricant leakage. Therefore,
the machine can be used without lubrication for long
periods. Replace the grease as described below.
1. Grease replacement period
After purchase, replace grease after every 6 months
of usage. Ask for grease replacement at the nearest
authorized Hitachi Service Agent. Proceed for
replacement of grease.
2. Grease replacement
CAUTION
Before replacing the grease, turn the power off and
pull out the power plug.
(1) Remove the crank case cover and wipe off the
grease inside. (Fig. 23)
(2) Supply 20g of Hitachi Electric Hammer Grease A
(Standard accessory, contained in tube) to the crank
case.
As the tube contain 30g of grease, supply 2/3 of
the contained grease.
(3) After replacing the grease, install the crank case
cover securely.
NOTE
The Hitachi Electric Hammer Grease A is of the low
viscosity type. If necessary purchase from an
authorized Hitachi Service Agent.

MAINTENANCE AND INSPECTION

1. Inspecting the tool
Since use of a dull tool will degrade efficiency and
cause possible motor malfunction, sharpen or
replace the tool as soon as abrasion is noted.
2. Inspecting the mounting screws:
Regularly inspect all mounting screws and ensure
that they are properly tightened. Should any of the
screws be loose, retighten them immediately. Failure
to do so could result in serious hazard.
3. Maintenance of the motor
The motor unit winding is the very "heart" of the
power tool. Exercise due care to ensure the winding
does not become damaged and/or wet with oil or
water.
English
8