Programming; Access To Main Programming Menus; Loading Default Parameters; Travel Learning - V2 HEAVY2 Manual De Instrucciones

25 - PROGRAMMING

The programming of the functions and times of the unit is carried
out through the configuration menus, accessible and searchable
through the 3 buttons
the unit.
ESA
f2 c1 c2
H1H2 H3 H4 H5 H6 H7 H8 E1 E2 E3 E4 E5
• By pressing OK button you can access the programming and
configuration menus of each individual parameters
• By pressing the button
Z6 Z5 Z4
OUTPUT
• By pressing the button
m
WARNING: Outside of the configuration menu, the
h i
buttons and activate the motor in DEAD MAN mode.
h
The button activates the command OPEN and the button
i
activates the command CLOSE.
m
These commands activate the motor without taking
into account the status of safety devices.
25.1 - ACCESS TO MAIN PROGRAMMING
MENUS
1. Press and hold the OK button until the display shows the
desired menu
Programming of the operating parameters
PRG
(Chapter 25.5)
Cycle Counter (Chapter 25.4)
CNT
Learning of the travel (Chapter 25.3)
SET
Loading DEFAULT parameters (Chapter 25.2)
DEF
2. Release the OK button: the display shows the first item in the
sub-men or the options available for the function.
PRG
CNT
SET
DEF
h i
3. Using the buttons
needed
m
CAUTION: if you do not carry out any operation for
more than 1 minute, the unit exits from the programming
mode, without storing the settings and changes made are
lost.
h i
FRONT PANEL
, and OK placed next to the display of
OVERLOAD
T1 T1
i
you will switch to the next item
Z3 Z2 Z1 W1 W2
h
you return to the previous item
MODE
Total / Service
Learn / Exit
Load default / Exit
and OK select and edit the parameters

25.2 - LOADING DEFAULT PARAMETERS

If necessary, you can reset all parameters to their DEFAULT values
(see table on page 46).
m
F2
WARNING: This procedure involves the loss of all
customized parameters.
F1
1. Press and hold the OK button until the display shows
2. Release the OK button: the display shows
3. To exit the function, select
OK to confirm
W3 W4 W5
MAINS
4. To load the DEFAULT data select
h i
buttons and press OK.
Then select
with their DEFAULT value, the unit leaves the programming
mode and the display shows the control panel

25.3 - TRAVEL LEARNING

This function allows you to store the limit switches.
The recorded values are useful for all the programming
parameters that are based on a percentage of the travel.
1. Press and hold the OK button until the display shows
2. Release the OK button: the display shows
3. To exit the function, select
OK to confirm
4. To start the learning procedure of the travel select
through the buttons
5. Press and hold the
6. Press and hold the button
7. Press the OK button: the display shows the value measured by
the obstacle sensor during
8. - To confirm the value displayed, press the OK button, then
select the menu
sensors, the limits of the travels and exit the function
- To change the value of the parameters
use the h and i buttons, press OK to confirm, then select
the menu
sensors, the limits of the travel and exit the function
- To store only the limits of the travel without changing the
obstacle sensor settings, wait 20" without pressing any
button: the unit exits the programming menu and displays
the control panel
- 45 -
Load default
Exit
using the
Exit
Load default
and press OK: all parameters are re-written
Yes
Learn
Exit
using the
Exit
h i
and and press then OK
h
button to open the door completely
i
to close the door completely
opening
SEN.A
and to store the values of the
FINE YES
and to store the values of the
FINE YES
DEF
h i
and press
using the
SET
h i
and press
Learn
and SEN.A SEN.C