Important Remarks; Programming - V2 RXP2S220 Manual De Instrucciones

IMPORTANT REMARKS

For technical information or any installation problem, you can call
our customer service during office hours
TEL. (+39) 01 72 81 24 11
V2 S.p.A. has the right to modify the product without
previous notice; it also declines any responsibility to
damage or injury to people or things caused by improper
use or wrong installation.
Please read this instruction manual very carefully
before installing and programming your devoce..
• This instruction manual is only for qualified technicians, who
specialize in installations.
• Every programming and/or every maintenance service should
be done only by qualified technicians.
• The installer must provide for a device (es. magnetotermical
switch) ensuring the omnipolar sectioning of the equipment
from the power supply.
• The standards require a separation of the contacts of at least
3 mm in each pole (EN 60335-1).
• The plastic case has an IP55 insulation; to connect flexible or
rigid pipes, use pipefittings having the same insulation level.
DICHIARAZIONE DI CONFORMITÀ
V2 SpA hereby declares that the products:
RXP2S220 / RXP2S120/ RXS2KB220 / RXS2KB120
comply with the following directives:
99/05/CEE radio
2006/95/CEE electrical safety
89/336/CEE electromagnetic compatibility
To verify compliance, the following technical standards have been
applied:
EN 60335-1, EN 55014-1, EN 55014-2, EN 301 489-1,
EN 301 489-3, EN 300 220 - 3
Racconigi, lì 10/09/2009
V2 S.p.A. legal representative
Cosimo De Falco
230V / 120V dual channel receiver, with the
ability to control loads up to 1500W
• Operation by means of Royal (mod. RXS2KB220 - RXS2KB120)
or Personal Pass (mod. RXP2S220 - RXP2S120) remote
controls.
• The RXP2S220 - RXP2S120 version enables you to store up to
83 different codes and cancel all the stored ones as well.
• IP55 plastic box.
Nominal Frequency
Alimentation
Relay contact
Working temperature
Consumption
Sensibility
S/N
Size
Weight

PROGRAMMING

The self learning programming system enables the code
memorization and the setting of the following functioning
modes:
MONOSTABLE: it activates the corresponding relay through the
time of TX transmission. When the transmission stops, the relay
goes automatically off.
BISTABLE: it activates the corresponding relay on the first TX
transmission. The relay goes off on the second transmission.
TIMER: the tx transmission activates the corresponding relay
which goes off after the set time (max 7,5 minutes).
PROGRAMMING OF THE MONOSTABLE
FUNCTION
To start programming, please proceed as follows:
1. Press and release the SW1 rx button for a number of times
as shown in the following table, in order to select the channel
you wish to program with monostable function.
SELECTED CHANNEL N°IMPULSES SW1
CHANNEL 1
CHANNEL 2
2. Press and keep pressed the tx button: if the rx led goes off,
it means the transmitted code has been correctly memorized.
IMPORTANT: to memorize the code in the correct way
it is necessary to keep a minimum distance of 1,5 metres
between the transmitter and the receiver's antenna.
230V models 120V models
433,92 Mhz
230Vac - 50Hz 120Vac - 60Hz
10A / 250Vac 10A / 120Vac
-20 ÷ +60 °C
100 mA stand by
≥ -102 dBm
> 17dB @ 100dBm, m=100%
113 x 113 x 57 mm
350 g
LED ON
L1 L2
•
1
•
2