Bosch PFS 3000-2 Manual Original página 23

Spraying capacity
Too much material on target ar-
ea:
Not enough material on target
area:
Adjusting the Air Flow (see figure D)
(AIRVolume)
– Set the sliding switch 24 to the appropriate application to
set the correct air flow and pressure for the spray material
used.
Off "Wood" application "Wall" application
Thin-viscosity spray
material
Work Breaks and Transport (see figures K
A carrying handle 22 and a carrying strap 21 are fitted to the
base unit to enable easy transport of the fine-spray system.
You can hang the base unit 20 across your shoulder during
work using the carrying strap 21.
The spray gun 1 can be put down on a flat work surface during
breaks. No spray material can leak out.
 Always put the spray gun upright on a flat surface when
it is filled with spray material. Spray material can leak
out from a spray gun if it is lying down.
Maintenance and Service
Maintenance and Cleaning
 Before any work on the machine itself, pull the mains
plug.
 Thoroughly clean the individual parts of the fine-spray
system after each use, especially all paint-carrying
components. Proper cleaning is a prerequisite for fault-
less and safe operation of the spray gun. No warranty
claims will be accepted if cleaning has not been done at all
or has not been done properly.
If the replacement of the supply cord is necessary, this has to
be done by Bosch or an authorized Bosch service agent in or-
der to avoid a safety hazard.
Bosch Power Tools
Adjustment
The spraying capacity must
be reduced.
– Turn down by one set-
ting.
The spraying capacity must
be increased.
– Turn up by one setting.
Thick-viscosity spray
material
L)
–
Cleaning (see figure M)
Always clean the spray gun and the container with the respec-
tive diluting agent (paint thinner or water) for the spray mate-
rial being used.
Never clean the nozzle and air holes in the spray gun with
pointed objects.
– Switch the base unit 20 off.
– Remove the air hose 18 both from the base unit 20 and
from the spray gun 1 (quarter turn of the bayonet lock 19
counterclockwise; pull the bayonet lock 19 out of the port
8/27).
– Clean the base unit if necessary with a cloth moistened
with diluting agent and then remove the base unit 20 and
the air hose 18 from the immediate cleaning environment.
– Press the trigger switch 5 on the spray gun so that the
spray material can flow back into the container.
– Unscrew the container 7 and empty the remaining spray
material back into the original spray material.
– Fill the container 7 halfway with the diluting agent (solvent
or water) and fit it to the spray gun 1 again.
– Shake the spray gun several times.
– Unscrew the container 7 and empty the container com-
pletely into an empty material tin.
– Remove the union nut 3, the air cap 2, the nozzle cap used
9/10 and the suction tube 15 with the container seal 14.
– Clean all paint-carrying parts in a bucket with diluting agent
using the cleaning brush 25 or a standard washing-up
brush.
Also clean the paint channel 17 of the spray gun 1.
– Check if the suction tube 15 and the container seal 14 are
free of spray material and undamaged.
If required, clean the container seal 14 again with diluting
agent.
Clean the ventilation hole 16 using the cleaning brush 25.
– Clean the outside of the container and the spray gun with a
cloth moistened in paint thinner.
– If required, clean the filling sieve 11 thoroughly with dilut-
ing agent.
– Before mounting, allow all components to dry thoroughly.
– Reassemble the fine-spray system in reverse order.
Cleaning the Air Filter (see figure N)
The air filter 29 must be cleaned occasionally. The air filter
must be replaced if it is heavily soiled.
– Open the air filter cover 26.
– Remove the air filter 29.
– Light soiling:
Tap the air filter 29 to empty it.
or
Heavy soiling:
Clean the air filter 29 under running water and then leave it
dry thoroughly to prevent mould from forming.
or
Replace the air filter 29.
– Reinsert the air filter.
– Close the air filter cover 26 again.
English | 23
2 609 007 771 | (28.2.14)