Yamaha YSP-900 Manual De Instrucciones página 270

Continued
Carry out the AUTO SETUP (IntelliBeam) procedure to adjust the settings that
from the front
best match your listening environment.
This unit employs the YAMAHA IntelliBeam technology with the aid of the supplied optimizer microphone, allowing you to achieve highly accurate sound adjustments
that best match your listening environment. Be advised that it is normal for loud test tones to be output during the AUTO SETUP procedure. Make sure that there are
no children around in the listening room while the AUTO SETUP procedure is in progress.
1
Press STANDBY/ON on
STANDBY/ON
the remote control.
The power of this unit turns on.
STB
If a subwoofer with adjustable volume and
crossover/high cut frequency controls is
VOLUME
connected to this unit, set the volume
between 10 and 12 o'clock as viewed on
a conventional clockface and set the
crossover/high cut frequency to the
maximum.
MIN MAX
Subwoofer
2
Turn on the power of your TV.
3
Select the appropriate video input
on your TV.
4
Set the operation mode selector to YSP.
CH LEVEL MENU
TV/AV
ENTER
YSP
TEST RETURN
5
Press and hold AUTO SETUP for more than 2
seconds.
The menu screen appears on the TV.
If the menu screen does not appear, check the video pin cable (connection
3 in the diagram on the front page) is connected properly and then press
YSP followed by MENU.
AUTO SETUP
STB VCR DVD AUX
TV
PREPARATION & CHECK
INPUT1 INPUT2 MACRO
Please connect the MIC.
TV
Please place the MIC at least
AUTO 1.8m/6ft away from the YSP
VOL MODE SETUP INPUTMODE SLEEP
unit. The MIC should be set
at ear level when seated.
Measurement takes about 3min.
After [ENTER] is pressed,
5BEAM ST+3BEAM 3BEAM
please leave the room.
1 2 3
[ENTER]:Start [RETURN]:Cancel
6
Check the following points.
POWER
POWER
・Is the optimizer microphone firmly connected to this unit?
AV TV
・Is the optimizer microphone placed in a proper loacation?
・Are there any large obstacles in between the optimizer microphone and the
walls in your listening room?
VCR DVD AUX
TV ・The AUTO SETUP procedure starts in 10 seconds after pressing ENTER
on step 7. To achieve the best results possible, evacuate yourself for your
CROSSOVER/
listening room until the AUTO SETUP procedure is completed.
HIGH CUT
・To cancel the AUTO SETUP procedure after it is started, press RETURN.
・The AUTO SETUP procedure takes about 3 minutes.
MIN MAX
Press ENTER to start the AUTO SETUP procedure.
7
The following screen appears on the TV and the AUTO SETUP procedure
starts in 10 seconds.
CH LEVEL MENU
TV/AV
ENTER
YSP
TEST RETURN
The setup screen automatically changes during the AUTO SETUP
procedure.
If any error occurs, the corresponding error message appears on the screen.
In this case, see "Error messages for AUTO SETUP" on page 33 in the
Owner's Manual and then follow the instructions. To start the AUTO SETUP
procedure once again, press RETURN and then carry out the procedure from
step 5.
When the AUTO SETUP procedure is complete, the following screen
appears on the TV.
SHOW RESULT
MEASUREMENT COMPLETE
BEAM MODE :5 BEAM
SUBWOOFER:NOT APPLICABLE
[ENTER]:Save set-up.
[RETURN]:Do not save set-up.
8
Press ENTER.
The result is confirmed and the following screen appears on the TV for 2
seconds and then the menu screen disappears from the TV.
The new settings are automatically saved in the system memory.
Disconnect the optimizer microphone and keep it in a safe place.
CH LEVEL MENU
TV/AV
ENTER
YSP
TEST RETURN
Enjoy TV or DVD audio in surround sound.
For instructions on your TV or DVD player, refer to the owner's manual supplied with each component.
Before carrying out the procedure below, set the volume of this unit to 30. If necessary, adjust the volume level in
step 4.
Enjoying TV in surround sound
1
Select the TV channel using
the remote control supplied
with your TV.
2
Set the operation mode selector to YSP .
AUTO SETUP START
Will begin in 10sec
3
Press TV on the remote
Please leave the room
**--------
control of this unit.
[RETURN]:Cancel
This unit switches to the TV playback mode.
4
If you hear sound output from your TV speakers, turn down the volume level
* This is an example of the result screen.
until you cannot hear any sound.
The result may differ depending on the
environment.
Use the remote control supplied with your TV.
5
Press VOLUME +/– on the remote control to adjust
the volume level of this unit.
6
Press one of the beam mode buttons on the
remote control to select the desired beam mode.
Select one of the three beam modes that best matches the current input source of
this unit.
AUTO SETUP COMPLETE For further information on the beam modes, see page 40 in the Owner's Manual.
Please remove the MIC from
the YSP and the listening
position.
To fine-tune the listening environment parameters manually or make advanced settings for
speaker positions, sound beams, etc., see "MANUAL SETUP" on page 57 in the Owner's Manual.
Enjoying surround sound
Enjoying DVDs in surround sound
1
Select the DVD video input on your
TV.
3
Press DVD on the remote control of this unit,
and then start playback on the DVD player.
This unit switches to the DVD playback mode.
TV
INPUT1 INPUT2 MACRO
TV
AUTO
VOL MODE SETUP INPUTMODE SLEEP
CH LEVEL MENU
TV/AV
ENTER
YSP
TEST RETURN
STB VCR DVD AUX
TV
INPUT1 INPUT2 MACRO
TV
AUTO
VOL MODE SETUP INPUTMODE SLEEP
VOLUME
CH TV VOL
MUTE TV INPUT TV MUTE
5BEAM
ST+3BEAM 3BEAM
1 2 3
STEREO MY BEAM SURROUND
4 5 6
MUSIC MOVIE SPORTS
7 8 9