Tabla de contenido
Idiomas disponibles
Idiomas disponibles
Align the filter holder with the bayonet fitting
N
in the brew head (13). Lock the filter holder in
place by turning the handle (15) to the right.
USE
Always check the water level in the
reservoir while using the appliance.
Never use the appliance without water in
the reservoir.
Before first use (fig. A)
Before first use, after a long period of non-use,
when the water reservoir has been removed,
or when water has completely run out, the
appliance must be cleaned and purged of air.
Fill the water reservoir (5) with cold water and
N
place it in the appliance.
Insert either of the two filters (16) into the filter
N
holder (14) without coffee. Place the filter holder
under the brew head (13) and lock it in place.
Place a cup on the drip tray cover, under the
N
brew head.
Insert the plug and switch the appliance on (1).
N
The heater light (4) will illuminate.
Turn the pump switch (2) on. A pumping noise
N
will be heard and after a few seconds water will
come out of the brew head. When it does, turn
the pump switch off.
As soon as the heater light extinguishes, turn
N
the pump switch on and let water flow into the
cup. When the cup is full, turn the pump switch
off. Empty the cup and repeat this procedure
once more.
Next, the steam nozzle should be cleaned as
follows:
Switch the appliance off and top up the water
N
reservoir. Place a cup under the steam nozzle (8).
Turn the pump switch on (2). The heater light (4)
N
will illuminate.
As soon as the heater light extinguishes, slowly
N
open the steam control knob (7) by turning it
anti-clockwise. Hot water will come out of the
steam nozzle.
Turn off the pump switch and close the steam
N
control knob by turning it fully clockwise.
Your espresso maker is now ready for use.
N
All manuals and user guides at all-guides.com
Purging the system
Before first use, after a long period of non-use,
when the water reservoir has been removed, or
when water has completely run out, air may have
entered the internal circuit. This air must be
purged from the appliance before use.
Press the on/off switch (1) to switch the
N
appliance on. The heater light (4) will illuminate.
Turn the pump switch (2) on. The pump will
N
start drawing water from the reservoir, making
a rumbling noise.
Turn the steam control knob (7) half a turn
N
counterclockwise. Air steam and hot water will
come out of the brew steam nozzle (8).
When hot water flows steadily from the steam
N
nozzle, close the steam control knob by
turning it fully clockwise.
Water will come out of the brew head (13).
N
Turn off the pump switch.
Making espresso (fig. A & B)
Carry out the actions described in "Assembly".
N
Add coffee as described in "Fitting the filter
N
holder to the brew head".
Press the on/off switch (1) to switch the
N
appliance on. The heater light (4) will illuminate.
As soon as the heater light extinguishes,
N
turn the pump switch (2) on. After a few
moments, espresso coffee will come out of the
brew head (13).
When the coffee cup is full, turn off the pump
N
switch and then switch off the appliance.
Carefully remove the filter holder (14) from the
N
brew head (13). A small amount of hot water
will be left on the coffee grounds. Pivot the
clamp (20) over the filter holder.
Keep the filter clamp pressed down and tap
N
the filter holder against the inside of a clean
bowl to remove the used coffee grounds.
Clean the filter (16) and the filter holder in hot,
N
soapy water.
Making cappuccino (fig. A & C)
Make espresso as described above. Use larger
N
cups.
Pour fresh milk into a frothing jug, suitable for
N
heating liquids.
E N G L I S H
7
Tabla de contenido
