1. General overview of equipment:
Accessories shown in the illustrations may vary from
model to model.
2. Hose connection:
Fit the hose inlet sleeve into the opening on the upper lid.
Apply soft pressure and turn the inlet sleeve approximately
half a turn to ensure it is firmly secured. Turn clockwise to
lock, anti-clockwise to release.
3. Adjustment of strap position on support plate:
On the primary strap, the position of the strap can be
adjusted for your individual comfort by moving the
adjustment plate to the inner or outer position.
4. Adjustment of tension ties on the strap's support
plate:
You can adjust the tension ties for your individual comfort.
Form a loop with your finger, then move the tie through the
clip forwards or backwards to the required length. Remove
your finger. Tension the tie.
5. Adjusting the vacuum cleaner to sit comfortably on
your back:
Pick up the vacuum cleaner. Put your arms through the
shoulder straps. Snap the waistbelt clip shut. Adjust
the length. Snap the chest clip shut. Adjust the straps
vertically by pulling down on both straps as shown in the
picture.
6. Tension tie clip:
Snap the two halves of the clip together. Make sure they
are securely fastened. To unlock, press both sides of the
clip simultaneously.
7. Cord set:
The electric cable can be held in place on the belt by
snapping the nylon tie around the coiled-up mains supply
cable. Roll up the electric cable starting at the machine.
8. Cable relieve:
Form a loop in the cable. Place the loop in the slot on the
cable relieve.
9. On/Off:
Plug the electric cable into the socket outlet. Press the
power switch for ON or OFF.
10. Dust bag:
When the suction power diminishes, it is time to replace
the dust bag. Check the bag frequently to make sure that
you don't overfill. Release the latches on the upper lid.
Lift up the lid from the container. Take hold of the
cardboard part of the dust bag and carefully lift the bag out
of the container. Some types of dust bag can be sealed to
prevent any dust/rubbish from being released.
In that case: Remove the protection foil. Fold the card
board and seal the bag.
11. Bag filter:
When you replace the dustbag it can be a good idea to
exchange or clean the bag filter. This can be done after
you have lifted out the dust bag. Clean the filter by shaking
it well. Put the bag filter into place or exchange it with a
new one if it's worned or damaged. Put a dust bag into
place and replace the upper lid and close the latches.
GENERAL INSTRUCTION FOR USE
12. HEPA filter:
HEPA filters cannot be cleaned or washed. Once they have
become dirty, they must be replaced. Check and change
the HEPA filter frequently. When handling a new HEPA
filter, avoid touching the surface of the filter. Take hold of
the plastic framework to ensure the HEPA filter functions
properly. The procedure for replacing HEPA filters: unlock
both latches on the motor top. Remove the container itself
and the upper lid. Turn the HEPA filter anti-clockwise. Lift
the filter. Repeat in reverse order to reassemble.
13. Pre filter:
Never vacuum without a pre-filter fitted into the machine.
Once the HEPA filter has been removed (see point no. 12
above) your can check and if necessary, replace the pre-
filter. Release the two latches on the motor top. Remove
the container and the upper lid. Place the new pre-filter in
the centre of the motor top. Lock both latches down.
14. Exhaust filter:
The filter cleans exhaust air from the vacuum cleaner.
Check and change the exhaust filter frequently. Press the
button downwards and open the cover. Fit the exhaust filter
into the cover. Fasten to the lower edge of the cover. Close
the cover.
15. Electro nozzle:
Plug the cable into the socket outlet on the side of the
machine. Power outlet for the Electro Nozzle is only
available on some variants.
16. Connection of bent end and handle grip:
Push the handle grip into the bent end until it is properly
fitted.
17. Extension tube:
The tube is telescopically adjustable. The length can be
adjusted by holding in the button and simultaneously
pulling or pushing the tube components until the properly
length is found. Some variants has a 2-piece tube.
18. Round brush nozzle:
Useful tool for cleaning home furnishings etc.
19. Combi nozzle:
One setting with brush (hard floors) and one without brush
for rugs (soft floors).
20. Crevice nozzle:
For cleaning tight spaces such as furniture, radiators,
corners and joints.
13