Miter Pointer Adjustment; Bevel Square To Table; Bevel Pointer; Bevel Stop Adjustment - DeWalt DW715 Manual De Instrucciones

Ocultar thumbs Ver también para DW715:
Tabla de contenido
Idiomas disponibles

Idiomas disponibles

pendicular to thefence, a s measured withthesquare.
Retighten the threescrews. P ayno attention t o the
reading ofthemiter pointer atthistime.
MITER POINTER ADJUSTMENT
(FIG. 5 ,6)
Tounlock, liftthemiter l ocklever ( J)upandsqueeze the
miter l atch (K)tomove themiter a rm tothezero position.
With themiter l ock lever u nlocked allow themiter l atch to
snapintoplace as you rotate the miterarmto zero.
Observe thepointer andmiter s cale through t heviewing
opening shown i nFigure 6 .Ifthepointer does notindicate
exactly zero, loosen t he screw holding thepointer inplace,
reposition thepointer and tighten t hescrew.
BEVEL S QUARE TOTABLE ( FIG. 2 ,7)
Toalign theblade square t otherotary t able, l ock thearm
inthedown p osition. Place a square a gainst theblade t ak-
ingcare tonothave thesquare o ntopofatooth. L oosen
thebevel lock knob (L) and ensure t he arm isfirmly a gainst
the0°bevel stop. M ove the0°bevel stop adjusting screw
asnecessary
sothat t heblade isatzero degrees bevel to
thetable. Ensure thebevel override levers ( N) arepushed
inward t oobtain a naccurate adjustment.
BEVEL P OINTER (FIG. 7 )
Ifthebevel pointer (M)does notindicate zero, l oosen t he
screw thatholdsit in placeandmove the pointer a s
necessary.
Donotremove t hesteel p late infrontofthe
bevel p ointer. This plate prevents wood resin fromaccu-
mulating onthebevel scale during use.
ADJUSTING
THE BEVEL S TOP TO45 °LEFT (FIG. 8)
NOTE: Adjust the45 °bevel angle o nly after p erforming
the
0° bevel a ngle andpointer a djustment. Ensure t he45 °
bevel o verride levers ( N)arepushed i nward t oobtain a n
accurate adjustment.
Toadjust theleft45 °bevel stop, first l oosen t hebevel lock
knob (L)and tiltthehead totheleft. I fthepointer does not
indicate exactly 45 °,turn theleftbevel stop screw until the
pointer reads 4 5°.
ADJUSTING
THE BEVEL S TOP TO33.85 °(FIG. 8 )
NOTE: Adjust the33.85 ° bevel angle only after p erforming
the0°bevel angle and pointer adjustment.
Tosetthe33.85 ° bevel angle, flipoutthestoppawl ( P).
Loosen thebevel lock knob (L)and tiltthehead t otheleft.
If thepointer doesnotindicate e xactly 3 3.85 °,turnthe
screw contacting
thepawl u ntil thepointer reads 3 3.85 °.
FENCE A DJUSTMENT
Turn OffandUnplug t heMiter S aw.
Inorder thatthesaw canbevel toafull48degrees leftor
right, thefences c anbeadjusted toprovide c learance. To
adjust afence, loosen t heplastic k nob (Figure 8 ,R),and
slidethefenceoutward. Make a dryrunwiththesaw
turned o ffand check f orclearance. Adjust thefence tobe
as close to theblade as practical to provide m aximum
workpiece support, without interfering witharmup and
down movement.
Tighten k nob securely. When thebevel
operations arecomplete, don't forget torelocate the fence.
FIG. 5
FIG. 6
MITER
SCALE
FIG. 7
POINTER
POINTER
ADJUSTMENT
SCREW
M
NOTE: The guide groove of the fences
can become
clogged with sawdust.
If you notice that it is becoming
clogged, use a stick or low pressure air to clear the guide
groove.
WARNING: Always use eye protection.
All users and
bystanders
must wear eye protection
that conforms
to
ANSI Z87.1. (CAN/CSA Z94.3)
AUTOMATIC ELECTRIC BRAKE
Your saw is equipped with an automatic
electric blade
brake which stops the saw blade within 5 seconds of
trigger release. This is not adjustable.
On occasion, there may be a delay after trigger release to
brake engagement. On rare occasions, the brake may not
engage at all and the blade will coast to a stop.
If a delay or "skipping" occurs, turn the saw on and off 4 or
5 times. If the condition persists, have the tool serviced by
an authorized DEWALT service center.
Always be sure the blade has stopped before removing it
from the kerf. The brake is not a substitute for guards or for
ensuring your own safety by giving the saw your complete
attention.
GUARD ACTUATION AND VISIBILITY
The blade guard on your saw has been designed to auto-
matically raise when the arm is brought down and to lower
over the blade when the arm is raised.
The guard can be raised by hand when installing
or
removing saw blades or for inspection of the saw. NEVER
RAISE THE BLADE GUARD MANUALLY UNLESS THE
SAW IS TURNED OFR
NOTE: Certain special cuts of large material will require
that you manually raise the guard. See page 11.
The front section of the guard is Iouvered for visibility
while cutting. Although
the louvers dramatically
reduce
flying debris, they are openings in the guard and safety
glasses
should
be worn
at all times
when
viewing
through the louvers.
MITER LOCK ADJUSTMENT
(FIG. 10)
The miter lock rod should be adjusted if the table of the
saw can be moved when the miter lock handle is locked
down. To adjust, put the miter lock handle in the up posi-
tion. Using a 3/32 hex wrench, loosen the set screw (W)
on the pivot pin. Using a slotted screwdriver,
adjust the
lock rod in 1/8 clockwise turn increments to increase the
lock force. To ensure the miter lock is functioning proper-
ly, re-lock miter lock handle to a non-detent miter angle.
Tighten set screw.
Brushes
DISCONNECT PLUG FROM POWER SUPPLY
Inspect carbon
brushes
regularly by unplugging
tool,
removing the motor end cap (Fig. 2), lift the brush spring
and withdraw the brush assembly. Keep brushes clean
and sliding freely in their guides. Always replace a used
brush in the same orientation in the holder as it was prior
Tabla de contenido
loading

Tabla de contenido