Troubleshooting - KENMORE ELITE 630.7793 Manual De Uso Y Cuidado

Dishwashers may occasionally exhibit problems that are unrelated to a malfunction of the dishwasher itself. The following
information may help you with a dishwasher problem without involving a repair professional.
Problem Cause
Dishwasher 1. Door may not be properly latched.
does not start 2. Unit may not be turned on.
3. Unit not reset or previous cycle not completed.
4. Delay start engaged.
5. Interruption of electrical power supply to dish-
washer or blown fuse.
6. The door may have been closed without first se-
lecting a cycle.
7. Water supply may not be turned on.
Dishwasher Default factory settings alert the customer that the
beeping cycle has completed by beeping. This feature can
(end of cycle be deactivated if so desired.
signal)
Display does 1. A fuse may have been blown or circuit breaker
not illuminate tripped.
or console 2. Door not closed or latched.
lights are not Note: For models with controls on the top portion of
on the door, the display only illuminates when the door is
opened and controls are visible.
Dishwasher 1. Incoming water is not warm enough.
seems to run 2. Cycle time can vary due to soil and water condi-
a long time tions.
3. Rinse agent dispenser is empty.
4. Dishwasher connected to cold water supply.
For typical cycle length, refer to Wash Cycles table
in Dishwasher Cycles and Options section of this Use
& Care Guide.
Dishes aren't 1. Spray arm movement is obstructed.
getting clean 2. Spray arm nozzles clogged.
enough 3. Improper use of detergents.
4. Filters could be clogged.
5. Dishes are nested or loaded too close together.
6. Selected wash cycle is not suitable for food soil
condtions.
Dishes are 1. Rinse agent dispenser is empty. (Rinse agent in-
not getting dicator is activated).
dry enough 2. Improper loading of dishes.
3. Selected cycle does not include drying.
Note: Plastic or Teflon do not typically dry as com-
pletely as other items due to their inherent proper-
ties.
All manuals and user guides at all-guides.com

TROUBLESHOOTING

Action
1. Shut the door completely.
2. Press the main power switch to turn unit on.
3. To reset, refer to "Canceling or changing the cycle" section
4. To reset, refer to "Delay Start" section in this manual.
5. Check circuit breaker.
6. Select a cycle and close the door.
7. Check and turn on water supply.
To adjust the volume or deactivate, refer to "Cycle Completion
Signal" section in this manual.
1. Check the fuse or circuit breaker box and replace the fuse
2. Ensure that door is properly latched and completely
1. Before starting a cycle, run hot water faucet at the sink
2. Sensors in the dishwasher automatically increase the cycle
3. Add rinse agent.
4. Verify dishwasher is connected to hot water supply plumbing.
1. Ensure that spray arm movement is not blocked by hand
2. Remove the spray arms and clean according to "Check/
3. Increase or decrease detergent depending on the water
4. Clean the filter. Refer to "Check/Clean the Filter System"
5. Rearrange load such that water spray can reach all items in
6. Refer to Wash Cycles table in Dishwasher Cycles and
1. Add rinse agent. The use of rinse agent improves drying.
2. Rearrange load to ensure items are not nested. Refer
3. Quick Rinse setting does not include drying cycle,
Note: Select models offer an extra heating options to improve
drying performance. Refer to "Wash Cycle options" under
the Operating the Dishwasher section of this manual.
17
in this manual.
or reset the breaker if necessary.
closed.
nearest to the dishwasher.
time to ensure a good wash when heavy soil is detected.
rotating spray arms.
Clean the Spray Arm Nozzles" in Care and Maintenance
section of this manual.
hardness. Refer to Table under "Adding Detergent and
Rinse Agent".
under Care and Maintenance section of this manual.
the dishwasher. See also "Preparing and Loading" section
of this manual.
Options section of this Use & Care Guide.
also to the "Preparing and Loading" section of this
manual.