Tabla de contenido
Use the fence to guide and support the work past the
saw blade. Unsupported cuts will shift and may cause the
work to be thrown backward.
Be aware of proximity of you hand/fingers to the cutting
tool. Non-through cuts are "blind cuts", use push sticks to
move the work through the cutter.
Use the proper table insert for the width and diameter of
the dado blade or molding head. Dado blade stack or
molding head is wider than the slot of the standard table
insert. These blades will strike and damage the standard
insert and cause severe injury by throwing the insert against
the operator.
Do not bevel with dado blades or molding heads. These
accessories are designed for perpendicular non-through
cutting.
Do not elevate the dado blade so that the hub protrudes
above slot of the table insert. Contact with hub will cause
the workpiece to be unstable as it passes through the cut
and possibly kickback.
Don't force the workpiece through the dado blade. Dado
blades create wide non-through cuts that require the
operator to feed the work slowly and use of feather boards
and positive downward pressure on the workpiece to avoid
loss of control.
Do not back up or pull the workpiece back (reverse feed)
when resawing. Pulling the workpiece backward could
cause kickback.
Double Insulation
is a design concept used in electric
power tools which eliminates the need for the three wire
grounded power cord and grounded power supply system. It
is a recognized and approved system by Underwriter's Lab-
oratories, CSA and Federal OSHA authorities.
IMPORTANT: Servicing of a tool with double insulation re-
quires care and knowledge of the system and should be
performed only by a qualified service technician.
Replace damaged cords immediately. Use
!
WARNING
of damaged cords can shock, burn or
electrocute.
Always use proper extension cord. If an
!
WARNING
extension cord is necessary, a cord with
adequate size conductors should be used to prevent
excessive voltage drop, loss of power or overheating. The
table shows the correct size to use, depending on cord
length and nameplate amperage rating of tool. If in doubt,
use the next heavier gauge. Always use U.L. and CSA listed
extension cords.
NOTE: The smaller the gauge number, the heavier the cord.
Double Insulated Tools
Extension Cords
"SAVE THESE INSTRUCTIONS"
5.
Table saws are highly versatile products capable of
performing variety of operations.
applications to be fully addressed in this manual. Go to
the library, home center, hardware or bookstore to learn
about the many applications of a table saw; we suggest
obtaining woodworking books like "The Table Saw Book"
by Richard J. de Cristoforo or similar publications addressing
your particular needs.
Some dust created by power sanding,
!
WARNING
sawing, grinding, drilling, and other
construction activities contains chemicals known to
cause cancer, birth defects or other reproductive harm.
Some examples of these chemicals are:
• Lead from lead-based paints,
• Crystalline silica from bricks and cement and other masonry
products, and
• Arsenic and chromium from chemically treated lumber.
Your risk from these exposures varies, depending on how
often you do this type of work. To reduce your exposure to
these chemicals: work in a well ventilated area, and work
with approved safety equipment, such as those dust masks
that are specially designed to filter out microscopic particles.
WHEN SERVICING, USE ONLY IDENTICAL REPLACE-
MENT PARTS.
POLARIZED PLUGS. If your tool is equipped with a polar-
ized plug (one blade is wider than the other), this plug will fit
in a polarized outlet only one way. If the plug does not fit fully
in the outlet, reverse the plug. If it still does not fit, contact a
qualified electrician to install the proper outlet. To reduce the
risk of electric shock, do not change the plug in any way.
RECOMMENDED SIZES OF EXTENSION CORDS
120 VOLT ALTERNATING CURRENT TOOLS
Cord Size in A.W.G.
Tool's
Ampere
Cord Length in Feet
Rating
25
50 100 150
3-6
18
16
16
6-8
18
16
14
8-10
18
16
14
10-12
16
16
14
12-16
14
12
—
There are too many
2
Wire Sizes in mm
Cord Length in Meters
15 30
60 120
14
.75 .75 1.5 2.5
12
.75 1.0 2.5 4.0
12
.75 1.0 2.5 4.0
12
1.0 2.5 4.0
—
—
— —
—
—
Tabla de contenido
