Tabla de contenido
Utilizzo
Use
Knowing the appliance
EN
The appliance is a special press to form pizza dough disks.
Fig.10.
Its operation is quite simple: lowering the protection grille
(O), the lower plate approaches the upper one until it reaches the
distance set with lever
(P); this way the dough ball is squashed
between the plates.
After the set time
the lower plate returns to the starting
position.
It is therefore necessary to set only 4 parameters for the operation:
temperature
• the
of the upper plate;
temperature
• the
of the lower plate;
distance
• the
between the plates
desired diameter of the dough disk;
how long
•
the plates must stay in contact
fixes the size of the dough disk after flattening it.
Knowing the control panel
Display
A
actual temperature
Displays the
In the parameter setting phase it displays the
set
for the upper plate or the
plates, pressing key (L).
Display led
B
If the LED is lit, it means that the element of the upper plate is
heating up to reach the set temperature. If the LED is off, the
set temperature has been reached.
Display
C
actual temperature
Displays the
In the parameter setting phase, it displays the
set
for the lower plate.
With the machine OFF, pressing the ON/OFF key (M) for a
few seconds displays the "countdown" time (programmed
switch-on).
Display led
D
If the LED is lit, it means that the element of the lower plate is
heating up to reach the set temperature. If the LED is off, the set
temperature has been reached.
+ key
E
temperature of the upper plate
Increases the
contact time
of the plates. With the machine OFF, it allows
the display (A) and (C) of the
out.
- key
F
temperature of the upper plate
Decreases the
contact time
of the plates.
+ key
G
temperature of the lower
Increases the
- key
H
temperature of the lower
Decreases the
Timer led
I
Fixed LED: with the machine ON, it means that the contact
time of the plates is being set.
Flashing LED: with the machine OFF, it indicates that the
programmed switch-on function is active.
Timer key
L
With the machine ON, it allows setting the displayed plate
contact time in seconds (A).
ON/OFF key
M
Turns the machine on and off; with the machine off, pressed
for a few seconds, activates the "countdown" function
(programmed switch-on).
Utilisation
Benutzung
this adjustment defines the
the contact time
Fig.10.
of the upper plate.
temperature
contact time
between the
of the lower plate.
temperature
or the
number of flattenings carried
or the
plate.
plate.
Uso
Эксплуатация
Emergency STOP button
N
When pressed, the red STOP button switches the machine off
and prevents the lower plate from raising in an emergency
(for instance if some foreign object remains stuck between
the plates).
It must therefore be used only when really necessary and not
as an ON/OFF switch to be used at the end of the work day.
If pressed, to restore the conditions of use, release the button
by turning it clockwise (the display will show the message
"PIF 197" which is NOT an alarm but indicates the version
of the board); then turn the machine back on with the
ON/OFF key (M) and restart the cycle as usual, i.e. lowering
the protection grille (1), to return the plate to the starting
position.
How to switch the appliance ON
Fig.11.
The machine is switched on by pressing the
key
(M).
After a few seconds, the display:
(A)
displays the actual temperature of the upper plate
(C)
displays the actual temperature of the lower plate.
If the machine does not switch on, check whether the
emergency STOP button
turning it in a clockwise direction.
How to set the parameters
SETTING THE PLATE TEMPERATURE
recommended temperature to be increased in case of intense work:
150°-160°C (302°F - 320°F)
Fig.12.
To set the temperature of the
"+" (E)
"-" (F)
key; the
display (A)
or
(E)
"-" (F) key
or
until the desired temperature is reached. The set
temperature is stored when the display stops flashing.
Fig.13.
To set the temperature of the
"+" (G)
"-" (H)
or
key; the
"+" (G)
"-" (H)
or
key until the desired temperature is reached.
The set temperature is stored when the display stops flashing.
SETTING THE PLATE CONTACT TIME
recommended time:
0.6 - 0.8 seconds
Fig.14.
You can set the contact time between plates from 0
to 10 seconds. To set this, press the
display (A)
lights up, the
"+" (E)
"-" (F)
press the
or
reached.
The set time is stored when the display stops flashing.
ADJUSTING THE DISTANCE BETWEEN THE PLATES
lever (P)
Fig.15.
Rotate the
the plates is reached.
Moving the lever:
anticlockwise
-
the distance between the plates
thinner
the dough disks are
clockwise
-
the distance between the plates
the dough disks are thicker.
stop (Q)
The
prevents you from decreasing the distance
between the plates and consequently the dough thickness
excessively.
44
is locked; if so, unlock it by
upper plate
starts to flash; press the
lower plate
display (C)
starts flashing; press the
"timer" (L)
key; the
starts flashing and shows the set time;
key until the desired temperature is
until the desired distance between
decreases
increases
ON/OFF
press the
"+"
press the
led (I)
Tabla de contenido
