General Conditions Of Use - neofeu NLDR Manual Del Usuario

by the letter A (single hanging points) or A/2 (obligatory to
attach both these points).
1: Shortening the lanyard: leave some slack at the large buckle
end and pull the manufactured side end (#3.1) for NLDR and
(#3.2) for NLSR.
2: Extending the lanyard: leave some slack at manufactured side
end and pull the large buckle end (#3.1) for NLDR and (#3.2)
for NLSR.
- In the work positioning configuration, the work positioning
lanyard must be adjusted in such a way that it is kept tensed.
- During use, check the equipment on a regular basis. Its
components must be protected from any environmental
stress: mechanical stress (impacts, sharp edges, etc.), chemical
stress (projection of acids, bases, solvents, etc.), electrical stress
(short-circuit, electric arcs, etc.) or thermal stress (hot surfaces,
blowtorches, etc.).
- The structural anchor point where the lanyard will be fixed
must be at the level of or above the user's height, at a reduced
distance and must have static strength of at least 12kN. In
addition, it must meet the requirement of the EN795:2012
standard.
- Avoid areas that are prone to the risk of falling.
- In the event of a fall, the equipment must be destroyed.
- If the user has to frequently open and close the connector
at the end, it is preferable to use a lanyard equipped with an
automatic locking connector. Otherwise, it is possible to use a
lanyard equipped with manual locking connectors.
- A connector must never have its load focused at its clasp.
- - In case of a NLSRxx or NLDRxx product (lanyard provided
without connector #2), the user must connect the lanyard
to the anchor point, the fall arrestor harness or the work
positioning belt by means of connectors compliant with the
EN362:2005 standard.

GENERAL CONDITIONS OF USE :

- A periodic inspection carried out by a competent inspector is
necessary to ensure the safety of the user, which is connected
to the maintenance of the effectiveness and resistance of the
equipment. A mandatory annual inspection will check the
condition of the equipment and it can only continue to be used
on obtaining a written agreement.
INTERPRETATION OF THE MARKING (#4) :
- 1 Ref : Product reference.
- 2 S/N: Serial number – Manufacturing batch.
- 3 Maximum length of the lanyard excluding connectors.
- 4 Date of manufacture.
- 5 Expiry date.
- 6 Manufacturer's identifier.
This product is compliant with Regulation 2016/425. It meets the requirements of harmonized standard
EN358: 2018. The declaration of conformity is available at : www.neofeu.com.
Notified body for UE type examination :
APAVE SUD EUROPE SAS (N°0082) – CS 60193 – F13322 MARSEILLE CEDEX 16
Notified body for production control :
AFNOR CERTIFICATION (N°0333) - 11, rue Francis de Pressensé - FR 93571 LA PLAINE SAINT DENIS Cedex
- Do not expose these products to temperatures less than -30°C
or more than +50°C.
- This equipment must not be used in any way contrary to these
specifications and under no circumstances should its limits be
exceeded.
- Storage: the product must be stored in a dry and well-
ventilated area, sheltered from any direct or indirect source of
heat and from ultra-violet rays. Drying wet equipment must be
performed in the same conditions.
- Cleaning and disinfection: exclusively with water and a neutral
soap.
- Packaging: use rot-proof and watertight protective packaging.
- Transport: packaged and sheltered from impacts or pressure
caused by the environment.
- The product must not be modified or repaired.
- Service life: NEOFEU fall-protection PPE are designed to last
for several years in normal conditions of use and preservation.
The service life depends on the use. Certain environments
that are particularly aggressive, marine, siliceous or chemical
can reduce the service life of PPE. In these cases, special care
must be taken regarding protection and the inspections before
use. The mandatory annual inspection will validate the correct
functioning of the mechanism and it can only continue to be
used on obtaining a written agreement from the manufacturer
, its representative or a competent person.
As concerns what has been mentioned above, the rough
estimate of the service life of the products, as recommended
by NEOFEU, is ten (10) years.
- Ensure that the identification sheet and the maintenance
monitoring table is kept up to date from the time of the
commissioning and during each inspection.
- 7 Contact address.
- 8 Pictogram requesting to read the instructions before use.
- 9 CE Marking / Notified body no.
- 10 Product standard : publication year.
- 11 Maximum nominal load : 140 kg.
DEX NLR -M-Ind.03 p 7 /32