Technical Specifications - Cardin Elettronica S38 Serie Manual De Instrucciones

CARDIN
Via Raffaello, 36- 31020 San Vendemiano (TV) Italy
Tel:
Fax:
email (Italy):
email (Europe):
Http:
RADIOPROGRAmmER S38 WITH PROGRAmmABLE CODE
REmARkS
These instructions are aimed at professionally qualified "INSTALLERS OF ELECTRICAL
EQUIPMENT" in conformity with the local standards and regulations in force.
This appliance must be used exclusively for the purpose for which it has been made.
Any non authorised modifications are to be considered improper and therefore dan-
gerous. The manufacturer accepts no liability for damage caused by, or situations
arising from, the improper use of these appliances.
Description
The S38 radio programming system consists of one or more transmitter and one or
more receivers which can be combined to meet the specific needs of the client.
The single channel radio receiver (with functions A, B, C, D) offers up to 16384 code
combinations per appliance set by a block of 14 three-way dip-switches.
Use
The radio programmer allows the remote activation of a single-phase motor 230Vac
350W, with dynamic functioning for the sequence open-stop-close.
Compatibility with RXPR:
• The transmitters are fitted with a jumper "JC" to maintain compatibility
with receivers of the series non "C".
- Jumper inserted: compatible with NON series "C" receivers
- Jumper not inserted: compatible with series "C" receivers
Transmitter versions
TRQ038200 Pocket size transmitters
TRQ038400 Pocket size transmitters
TRQ038800
Pocket size transmitters
TRQ383200 Miniature transmitters
TRQ383400
Miniature transmitters
TRQ738200 Miniature transmitters
TRQ738400 Miniature transmitters
Receiver versions
RPQ038 Radio programmer
Receiver antenna installation
Minimum and maximum range of the radio controls.
"Range" is intended to mean the working distance, measured in free space, between
the receiver and the transmitter with the antenna installed. The range is therefore closely
linked to the technical characteristics of the system (power and sensibility) and varies
according to the characteristics of the site in which the system is located.
It therefore follows that to obtain the best results from the radio control the installation
sites for the receiver and the antenna should be carefully chosen.
It is not possible to install 2 receivers at a distance of less than 1,5 m from each
other. It is good practise to position the receiver away from computer systems, alarm
systems and other possible sources of disturbance.
(A bad choice of positioning could compromise the performance of the
receiver).
ANTENNA
The installation of the antenna is fundamental, connected to the receiver it represents
the reception point for the radio control.
When installing the antenna the following points should be observed:
- Only use a tuned antenna connected to the receiver using a coaxial cable RG58
(impedance 50Ω) with a maximum length of 15m.
- The antenna should be positioned out of doors in the highest possible point, visible
and away from metal structures.
N.B. If for some particular reason it is not possible to fit an antenna, a reasonable
performance can be obtained by connecting a 2,5m piece of single pole conductor
wire (Ø1mm) to the receiver.
INSTALLATION
Depending on the type of installation, work out the position in which the programmer
will be situated remembering that the site must be:
- a position safe from accidental collision;
- high enough above the ground to be safe from pools of water;
- in a position which the technician can easily reach.
The fixing of the case type receiver is carried out by using "fast-fitting" brackets. The
bracket should be fixed to the wall using two raw plugs (check that it is plumb to the
wall), the case can then be slid onto the bracket and fastened securely to the wall.
The slot-in circuit located towards the bottom of the case can be easily extracted to
facilitate wiring up the device.
If any repair work is necessary the case can be easily extracted by pushing upwards
the action of which will separate it from the bracket.
ELECTRICAL CONNECTION (fig. 5)
Before connecting the device to the mains make sure that:
- the voltage and frequency rated on the data plate conform to those of the mains
supply;
- a bipolar circuit breaker which leaves at least 3mm between the contacts has been
installed between the device and the mains;
ELETTRONICA spa
+39/0438.404011-401818
+39/0438.401831
[email protected]
[email protected]
www.cardin.it
2 channels
4 channels
8 channels
2 channels
4 channels
2 channels
4 channels
SERIAL NUMBER
ZVL127.03
The S38 series conforms to the essential requirements of the directive 99/05/CE
and the technical reference standards have been applied. This product has been
tried and tested in the manufacturer's laboratory, during the installation of the pro-
duct follow the supplied indications carefully.
- the high voltage 230V wires pass through the holes marked "A" and are routed sepa-
rately from the low voltage wires which pass through the holes marked "B";
- the wires are fastened down using a cable clamp;
- once the wiring is complete the holes through which the wires have passed have been
sealed using silicon;
- the holes which are not used are sealed by inserting the sealing caps "D".
• The appliance must be earthed, to this end there is a binding post marked with the
symbol to which the earth wire must be attached.
• Only low voltage circuits may be wired to the external circuit binding posts.
TERmINAL BOARD CONNECTIONS (fig. 5)
1-2 Earth connection
3-4 Radioprogrammer power supply 230 Vac 50-60 Hz
5-6-7 Motor control in output 350 W Close-Open-Neutral
8-9 TD Dynamic button in input (contact N.O.)
10-11 FTCII Contact N.C. in input for safety devices with travel direction inversion.
Any eventual safety devices must be powered by an external power circuit
12 Antenna braid
13 Radio receiver antenna
Settings (fig. 5)
TL Work cycle regulation trimmer (3...120 sec.). The timer countdown starts after an
opening or closing command has been received and stops after the programmed
work time has elapsed.
PW Power on LED
STS Lit: work cycle in course;
Flashing: photoelectric cell in alarm.
TRANSmITTERS
In the transmitters each button corresponds to a different function, with the sole excep-
tion of the two button transmitters where it is possible to have the same function for
both buttons (single-channel operation). For double-channel operation which can be
obtained using the second key, set the two-way DIP-SWITCH, located separately from
the fourteen-way user code DIP-SWITCH on the printed circuit board. Once the trans-
mitter's functions have been programmed and recognized, make sure that the jumper
position in the radio programmer corresponds to the desired function.
PROGRAmmING THE USER CODE
The transmitters and receivers are supplied with a block of DIP-SWITCHES (ON/OFF)
with which to program the digital codes for each system. Programming can be car-
ried out more than once, even after the installation, thus ensuring the total secrecy of
the user code. A 14 way DIP-SWITCH with 16384 combinations is available for the
programming of the radioprogrammer and transmitter user codes.
The use of transmitters with 8 keys allows code programming by means of a 13-way
DIP-SWITCH (Dip 14 always "ON") with 8192 combinations.
To ensure an exact match between the transmitter and receiver codes, when program-
ming the various functions must be taken into account.
Functions
The desired functions in the receiver are selected by setting the jumper situated on
the circuit board. The functions are printed on the circuit board in silk-screen form A,
B, C, D.

TECHNICAL SPECIFICATIONS

RECEPTION FREQUENCY
Attention: The transmission frequency of these products varies according
to the approved frequency and eventual personalisation in the country of
destination
Country Frequency
Italy 30,875 MHz
Europe 27,195 MHz
USA 27,195 MHz
RECEIVER
- local oscillation frequency tolerance .............................................30p.p.m. (-10°... +55°)
- intermediate frequency .........................................................................................455kHz
- impedance in input .................................................................................................... 50Ω
- sensibility .................................................................................................................0.5µV
- local oscillation emission .................................................................. <-70dBm (<100pW)
- power supply ........................................................................................ 230V ac 50-60Hz
- operating temperature range ........................................................................-20°...+60°C
TRANSmITTERS
- carrier frequency tolerance .................................................30p.p.m. from -10° to +55°C
- band width ................................................................................................ 10kHz/ ± 5kHz
- apparent radiated power ........................................................ -10...-7dBm (100-200µW)
- apparent power harmonic products ..................................................... <-64dBm (<1nW)
- power output adjacent channel (± 10 kHz) ........................................ <-37dBm (<0.2µW)
- modulation .......................................................................................................... AM/ASK
- signal modulation.....................................................................................PCM, 1.3ms/bit
- power supply ...............................................................................................9/12V ± 10%
- maximum power consumption ............................................................................. <38mA
- operating temperature range .......................................................................- 20... +70°C
- relative humidity ...................................................................................................... <95%
SERIES MODEL
S38 RXPR 25-03-2004
Antenna
ANQ730
ANQ727
ANQ727
DATE