General Information; Manual Purpose; Terminology And Symbol Legend; Product Identification - Lavor DYNAMIC A4 Manual De Instrucciones

2. GENERAL INFORMATION

2.1

MANUAL PURPOSE

To make it easier to read about and look up various
subjects, refer to the table of contents at the begin-
ning of the section in your language.
This manual has been prepared by the manufacturer
and is an integral part of the product. As such, it must
be kept in a safe place for the machine's entire service
life until demolition.
The customer must ensure that machine operators
have read or are familiar with the contents of this
manual so that they strictly follow the instructions
described herein.
Constant compliance with the instructions provided
in this manual is the only way to guarantee the best
results in terms of safety, performance, efficiency and
service life of the product you now own. Non-compli-
ance with these rules may cause injuries to people
and damage to the machine, the scrubbed surface
and the environment: in no case can such injuries or
damage be attributed to the manufacturer.
This manual refers in detail to the machine and pro-
vides instructions and descriptions only about our bat-
teries and battery chargers (optional).
The batteries and the battery charger are basic com-
plementary machine parts and will affect its operation
in terms of running time and performances. Only the
correct combination of the two accessories (batteries
and battery charger) will ensure the highest possible
performances and avoid wasting lots of money. For
more detailed information refer to the special battery
and battery charger manuals.
Our recommended battery chargers and batteries
(optionals) ensure the best combination with the
machine and offer outstanding versatility (battery
charger) as well as the category's highest quality and
performance standards.
2.2 TERMINOLOGY AND SYMBOL LE-
GEND
For the sake of clarity and to efficiently highlight the
various aspects of the instructions provided, terms
and symbols were used that are defined and illus-
trated here below:
- Machine. This definition replaces the commercial
name to which this manual refers.
- Operator. An operator is considered the person
who normally uses the machine and is familiar with
its operating features but does not have the specific
technical skills to work on that machine.
- Technician. A technician is considered a person
who has the experience, technical education, legis-
lative and regulatory knowledge that allows him to
carry out any type of required work, and the ability to
recognise and to avoid possible risks during machine
installation, operation, handling and maintenance.
- INDICATION SYMBOL (
tant information to avoid machine malfunctions.
- ATTENTION SYMBOL (
mation to avoid serious damage to the machine and
) Particularly impor-
☞
•
) Very important infor-
to the environment in which it operates.
- DANGER SYMBOL (
serious (or extreme) consequences affecting the
health of persons and causing damage to the product
and the environment in which it operates.
2.3

PRODUCT IDENTIFICATION

The nameplate located under the dashboard, above
the battery connector, contains the following informa-
tion:
- manufacturer ID
- CE mark
- model code
- model
- overall power rating
- serial number
- year built
- weight with maximum load
2.4

SPECIFIC USE

This machine is a floor scrubber-drier: it must be used
to scrub and to vacuum liquids of flat, rigid, horizon-
tal, smooth or moderately rough and uniform floors
that are free from obstacles in both civic and indus-
trial environments. Any other use is prohibited.
Please refer very carefully to the safety information
reported in this manual.
The scrubber-drier distributes a quantity of a water
and detergent solution (adjustable) on the surface
to be cleaned, while the brushes remove any dirt on
the ground. The machine's suction system, using a
ground squeegee, perfectly dries the liquids and the
dirt just removed from the front brushes in a single
pass.
By efficiently combining a cleaning detergent with
various types of brushes (or abrasive disks), the ma-
chine can adapt to all the various combinations of
floors and dirt.
2.5

TECHNICAL MODIFICATIONS

This machine was designed and built in accordance
with the fundamental requirements for user safety
and health as set forth in European directives. For this
reason the CE mark was placed on the ID label. The
European directives to which the equipment conforms
are referenced in the Certificate of conformity an-
nexed to this manual. This certificate will no longer be
valid if the equipment is modified in any way without
the manufacturer's prior authorisation.
The manufacturer reserves the right to make techni-
cal modifications to the product, without prior notice,
in order to make the necessary technical upgrades or
improvements. For this reason, some details of your
machine may be different from the information in the
sales catalogues or from the illustrations presented
in this booklet. However, this will not reduce safety
or invalidate the information supplied to this regard.

3. SAFETY INFORMATIONS

3.1

BASIC RECOMMENDATIONS

27
•
) Vital information to avoid