DeWalt DCD460 Manual Del Usuario página 33

InDIcaTOR DIaGnOsIs
OFF Tool is
functioning
normally
SOLID Anti-Rotation
has been
activated
(ENGAGED)
Bail Handle (Fig. D)
A bail handle 1 is provided for carrying the tool and for use as
an additional handle. Assemble the bail handle in one of the
positions shown in Figure D. When changing the location of the
bail handle from one position to the other, completely remove
the two bail handle bolts 5 securing it. Flip the handle over
and reinstall.
Side Handle (Fig. E)

WARNING: To reduce the risk of personal injury, always
operate the tool with the side handle properly installed
and tightened. Failure to do so may result in the side
handle slipping during tool operation and subsequent loss
of control. Hold tool with both hands to maximize control.
The two position side handle
13
side of tool. Thread the side handle
bolt 5 or directly into threaded holes
Tighten securely by hand.
ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.

WARNING: Use only D
e
Inserting and Removing the Battery Pack
from the Tool (Fig. B)
nOTE: Make sure your battery pack
To Install the Battery Pack into the Tool
Handle
1. Align the battery pack 11
handle (Fig. B).
2. Slide it into the handle until the battery pack is firmly seated
in the tool and ensure that you hear the lock snap into place.
To Remove the Battery Pack from the Tool
1. Press the release button 12
out of the tool handle.
2. Insert battery pack into the charger as described in the
charger section of this manual.
sOLUTIOn
Follow all warnings and
instructions when operating
the tool.
With the tool properly
supported, release trigger.
The tool will function
normally when the trigger
is depressed again and the
indicator light will go out.
can be assembled into either
13 into the bail handle
14 on desired side.
WALT battery packs and chargers.
11 is fully charged.
with the rails inside the tool's
and firmly pull the battery pack
Fuel Gauge Battery Packs (Fig. B)
Some D WALT battery packs include a fuel gauge which
e
consists of three green LED lights that indicate the level of
charge remaining in the battery pack.
To actuate the fuel gauge, press and hold the fuel gauge button.
A combination of the three green LED lights will illuminate
designating the level of charge left. When the level of charge
in the battery is below the usable limit, the fuel gauge will not
illuminate and the battery will need to be recharged.
nOTE: The fuel gauge is only an indication of the charge left on
the battery pack. It does not indicate tool functionality and is
subject to variation based on product components, temperature
and end-user application.
Speed Selector (Fig. A)
NOTICE: Risk of tool damage. Do not rotate the speed
selector lever while the drill is running or coasting, damage
may occur to the tool.
Rotate the speed selector lever
1 = low speed
2 = high speed
nOTE: The first time the tool is run after changing speeds, you
may hear a click on start up. This is normal and does not indicate
a problem.
Variable Speed Trigger Switch (Fig. A)
Depressing the variable speed trigger switch
on, releasing the variable speed trigger switch turns the tool off.
The variable speed trigger switch permits speed control—the
farther the trigger is depressed, the higher the speed of the drill.
Forward/Reverse Button (Fig. A)
A forward/reverse button determines the direction of the
3
tool. It is located in front of the trigger switch.
To select forward rotation, release the trigger switch
depress the forward/reverse button on the right side of the tool.
To select reverse, depress the forward/reverse button on the left
side of the tool. When changing the position of the button, be
sure the trigger is released.
nOTE: The first time the tool is run after changing the direction
of rotation, you may hear a click on start up. This is normal and
does not indicate a problem.
Keyed Chuck (Fig. A)
Open the chuck jaws by turning collar by hand and insert the
shank of the bit about 19 mm into chuck. Tighten the chuck
collar by hand. Place chuck key (
holes, and tighten in clockwise direction. It's important to
tighten chuck with all three holes. To release the bit, turn the
chuck counterclockwise in just one hole, then loosen the chuck
by hand.
nOTE: When using hex shank or three-sided shank bits, be sure
to align the flat sides of the bit with the chuck jaws to ensure
the bit is properly engaged by the jaws.
EnGLIsh
2 to the desired speed:
4 turns the tool
4 and
10 , Fig. A) in each of the three
31