Technical Data; Noise/Vibration Information; Declaration Of Conformity - Berner BAG 230-1 CLB Manual Original

OBJ_BUCH-1019-004.book Page 19 Wednesday, August 12, 2015 4:12 PM

Technical Data

Angle Grinder
Art. No.
Rated power input
Output power
Rated speed
Grinding disc diameter, max.
Thread of grinder spindle
Thread length (max.) of grinder spindle
Restarting Protection
Reduced starting current
Rotatable main handle
Run-on Brake
Weight according to EPTA-Procedure
01:2014
– with vibration-damping auxiliary
handle
– with standard-auxiliary handle
Protection class
The values given are valid for a nominal voltage [U] of 230 V. For different voltages and models for specific countries, these
values can vary.
Starting cycles generate brief voltage drops. Interference with other equipment/machines may occur in case of unfavour-
able mains system conditions. Malfunctions are not to be expected for system impedances below 0.25 ohm.

Noise/Vibration Information

Sound emission values determined according to
EN 60745-2-3.
Typically the A-weighted noise levels of the product
are: Sound pressure level 93 dB(A); Sound power
level 104 dB(A). Uncertainty K =3 dB.
Wear hearing protection!
Vibration total values a (triax vector sum) and un-
h
certainty K determined according to EN 60745-2-3:
Surface grinding: a = 7.5 m/s
h
Disk sanding: a = 4.5 m/s
h
The vibration level given in this information sheet
has been measured in accordance with a standard-
ised test given in EN 60745 and may be used to
compare one tool with another. It may be used for
a preliminary assessment of exposure.
The declared vibration emission level represents
the main applications of the tool. However if the
tool is used for different applications, with different
accessories or insertion tools or is poorly main-
tained, the vibration emission may differ. This may
significantly increase the exposure level over the
total working period.
An estimation of the level of exposure to vibration
should also take into account the times when the
tool is switched off or when it is running but not ac-
tually doing the job. This may significantly reduce
the exposure level over the total working period.
Identify additional safety measures to protect the
operator from the effects of vibration such as:
maintain the tool and the accessories, keep the
hands warm, organisation of work patterns.
1 609 92A 1D1 • 12.8.15
BAG 230-1 CLBB BAG 230-1 CLB BAG 230-1 CLBF
W
W
-1
min
mm
mm
kg
kg
2 2
, K=1.5 m/s ,
2 2
, K=1.5 m/s .
201168 201167
2400 2400
1600 1600
6500 6500
230 230
M 14 M 14
18




6.6
6.5
/II

Declaration of Conformity

We declare under our sole responsibility that the
product described under "Technical Data" is in
conformity with all relevant provisions of the direc-
tives 2011/65/EU, until 19 April 2016:
2004/108/EC, from 20 April 2016 on:
2014/30/EU, 2006/42/EC including their amend-
ments and complies with the following standards:
EN 60745-1, EN 60745-2-3.
Technical documents at:
Berner Trading Holding GmbH
Bernerstraße 6
74653 Künzelsau
GERMANY
Armin Hess
Chairman of the Management Board
06.08.2015, Berner Trading Holding GmbH
Bernerstraße 6
74653 Künzelsau
GERMANY
206972
2400
1600
6500
230
M 14
25 25
 –
 
 
– –
6.1 6.1
6.0 6.0
/II /II
English | 19