Use And Maintenance - Gorenje DC9635X Manual De Utilización

blanks with a screwdriver or other suitable tool, and fix the air
outlet flange with the screws as shown in Figure 1C.
If you install the unit in its suction version and place the engine
over the hood, remove the metal blank with a screwdriver or
other suitable tool, and tighten the engine group by using
the screws provided (Fig. 1B).
- Make the hole in the ceiling to accommodate the device
taking into account the dimensions shown in Figure 2.
ATTENTION: Make sure that the ceiling structure supports
the unit's weight. If not, prepare a suitable frame to fulfil
such function.
- Tighten the power box over the upper part of the hood using
the screws provided (Fig. 5).
- With a fitting pipe, connect the flange (Fig. 1C) to the air
extraction hole.
- Take the unit and place it inside the hole, just as you did in
the ceiling. Make sure that the brackets are perfectly hooked
(Fig. 6A).
- Tighten the brackets by using the screws inside the hood, as
shown in Figures 6B and 6C.
- If necessary, there is also the possibility of fixing the device
with additional screws from inside the hood to an under-
counter light (if present) (Fig. 2A).
- For different types of assemblies, use screws and anchors
that are suitable for the wall material (e.g.: reinforced concrete,
plasterboard, etc).
If the screws and anchors are provided with the product,
make sure that they are suitable for the type of wall to which
the hood is fixed.

USE AND MAINTENANCE

• We recommend that the cooker hood is switched on before
any food is cooked. We also recommend that the appliance is
left running for 15 minutes after the food is cooked, in order
to thoroughly eliminate all contaminated air.
The effective performance of the cooker hood depends on
constant maintenance; the anti-grease filter and the active
carbon filter both require special attention.
• The anti-grease filter is responsible retaining the grease
particles suspended in the air, therefore it is subject to
clogging with variable frequency according to the use of the
appliance.
- To prevent the danger of possible fires, at least every 2
months one must wash the anti-grease filters by hand using
non-abrasive neutral liquid detergents or in the dishwasher
at low temperatures and on short cycles.
- After a few washes, colour alterations may occur. This does
not give the right to claim their replacement.
• Before remounting the anti-grease filters and the rege-
nerable active charcoal filters it is important that they are
completely dry.
• Clean the hood frequently, both internally and externally,
using a cloth dampened with denatured alcohol or neutral
liquid detergents that are non abrasive.
• The lighting .system is designed for use during cooking
and not for the prolonged general lighting of the room. The
prolonged use of the lighting system significantly decreases
the average duration of the bulbs.
• If the appliance is equipped with courtesy lights it is possible
to use them for general room lighting for a prolonged amount
of time.
• Attention: The non compliance with the hood cleaning
warnings and with the replacement and cleaning of the filters
entails risk of fires. One therefore recommends keeping to the
suggested instructions.
• Replacing halogen light bulbs (Fig.9):
To replace the halogen lamps, B push the watch glass C and
open the flap. Replace them with a light of the same type.
Attention: Do not touch the lights with your hands.
If the appliance version includes LED lamps, the intervention
of a specialised technician is necessary to replace them.
• Commands (Fig.10):
NOTE: All units' functions are controlled through a remote
control.
If the remote control stops functioning (because of low
batteries, etc.) you can directly use the control inside the
unit (Fig. 8-10).
Power Button (A) = The on/off button switches on and off
the whole hood (motor and lights).
By pressing the button the motor starts at 1st speed.
Fan Speed button (B) = From the OFF position, press once
for the 1st speed, twice for the 2nd speed and three times
for the 3rd speed. In order to activate the intensive speed,
press the button for 5 seconds regardless of the status of the
hood. For each speed only the led indicating the set speed
will turn on. The intensive speed is indicated by the flashing
of the led indicating speed 3. The duration of the intensive
speed is 10 minutes; after this time the hood goes back to
the last set speed.
In order to remove the intensive speed press the power button
and the hood will switch off, or press the Fan speed button
and the speed goes back to the previously set one. Speed of
the hood with cyclic trend.
Light button (C) = There are three light levels: High, me-
dium, low.
From the off position press once for the high level, twice for
the medium level, three times for the low level and four times
to turn the lights off.
The level of the lights has a cyclic trend: High, medium,
low, off.
Timer button (D) = With any type of speed (excluding the
intensive speed), by pressing the button, the timer function is
activated for 15 minutes. After this time has elapsed the hood
will turn off (motor and any light on).
Lights indicator (E) = The lights indicator will switch on when
the lights are on at any level.
Filters indicator (F) = After 30 minutes of operation, the led
of the filters indicator will switch on, not flashing indicating
that the anti-grease filters have to be washed. To reset the
function (with the hood off ), press the Fan speed button for
5 seconds. After this operation, the led of the filters indicator
turns off and the setting of the 30 hours starts again from
the beginning.
Clean air indicator (8).
With the hood off, press the Power button (1) for 5 seconds to
activate the clean air function. This will switch on the motor
at speed 1 for 10 minutes every hour. The light indicator will
switch on without flashing and the led of the 1st speed will
switch on. In the remaining 50 minutes the light indicator will
flash. The function can be deactivated by pressing any button
except for the lights one.
THE MANUFACTURER DECLINES ALL RESPONSIBILITY
FOR EVENTUAL DAMAGES CAUSED BY BREACHING THE
ABOVE WARNINGS.
- 17 -