Use And Maintenance - Gorenje WHT921E3XBG Manual De Utilización

pane C using a lever action on the relevant cracks.
Replace the bulbs with new ones of the same type.
Caution: do not touch the light bulb with bare hands.
• FIXING TO THE WALL
Drill the holes A respecting the distances indicated (Fig.2).
Fix the appliance to the wall and align it in horizontal
position to the wall units. When the appliance has been
adjusted, definitely fix the hood using the screws A (Fig.5).
For the various installations use screws and screw anchors
suited to the type of wall (e.g. reinforced concrete, plaster-
board, etc.). If the screws and screw anchors are provided
with the product, check that they are suitable for the type
of wall on which the hood is to be fixed.
• FIXING THE DECORATIVE TELESCOPIC FLUE
Arrange the electrical power supply within the dimensions
of the decorative flue. If your appliance is to be installed in
the ducting version or in the version with external motor,
prepare the air exhaust opening. Adjust the width of the
support bracket of the upper flue (Fig.3). Then fix it to the
ceiling using the screws A (Fig.3) in such a way that it is in
line with your hood and respecting the distance from the
ceiling indicated in Fig.2. Connect the flange C to the air
exhaust hole using a connection pipe (Fig.5).
Insert the upper flue into the lower flue. Fix the lower flue
to the hood using the screws B provided (Fig.5), extract
the upper flue up to the bracket and fix it with the screws B
(Fig.3).
If your appliance has the lower connections indicated as
in Fig. 4 A, the fixing to be carried out is that shown in Fig.
6 A
To transform the hood from a ducting version into a filter-
ing version, ask your dealer for the charcoal filters and
follow the installation instructions.
• FILTERING VERSION
Install the hood and the two flues as described in the
paragraph for installation of the hood in ducting version.
To assemble the filtering flue refer to the instructions con-
tained in the kit. If the kit is not provided, order it from your
dealer as accessory. The charcoal filters must be fitted in
the ducting unit located inside the hood (Fig.9-10).

USE AND MAINTENANCE

• We recommend that the cooker hood is switched on before
any food is cooked. We also recommend that the appliance
is left running for 15 minutes after the food is cooked, in
order to thoroughly eliminate all contaminated air.
The effective performance of the cooker hood depends on
constant maintenance; the anti-grease filter and the active
carbon filter both require special attention.
• The anti-grease filter is used to trap any grease particles
suspended in the air, therefore is subject to saturation (the
time it takes for the filter to become saturated depends on
the way in which the appliance is used).
The acrylic filter, which is found resting on the grille, should
be replaced when the text, visible through the grille,
changes colour and the ink spreads; the new filter should
be fitted in such a way that the text can be seen through
the grille from outside the cooker hood.
If the filters do not have any text on them, or if metal filters
or aluminium panel filters are used, they should be washed
every 2 months in order to prevent the risk of fire. To wash
the filters, proceed as follows:
- Remove the filter from the grille and wash it using a
solution of water and neutral liquid detergent, leaving the
dirt to soften.
- Rinse thoroughly with warm water and leave to dry.
The metal filters and/or aluminium panel are also
dishwasher safe. If the filters are made using aluminium,
or if an aluminium panel is used, after a few washes the
colour may change. This does not mean they have to be
replaced.
If the replacement and washing instructions are not
followed, the anti-grease filters may present a fire hazard.
• The active carbon filters are used to purify the air which
is released back into the room. The filters are not washable
or re-usable and must be replaced at least once every four
months. The active carbon filter saturation level depends
on the frequency with which the appliance is used, the type
of cooking performed and the regularity with which the anti-
grease filters are cleaned.
• Remove build-up from the fan and other surfaces of the
cooker hood regularly using a cloth moistened with
denatured alcohol or non-abrasive neutral liquid detergent.
• The light on the cooker hood is designed for use during
cooking and not for general room illumination. Extended
use of the light reduces the average duration of the bulb.
COMMANDS: (Fig.14)
Push-button A = on/off lights switch
Push-button B = on/off cooker hood switch. The appli-
ance switches on at speed level 1, If the cooker hood is
on depress the push-button for 2 sec. to switch off the
cooker hood. If the cooker hood is at speed level 1 it will
not be necessary to depress the push-button to switch the
cooker hood off. Decreases the motor speed.
Display C = indicates the motor speed level selected and
activates the timer.
Push-button D = switches on the cooker hood. Increases
the motor speed. Touching the key at 3rd speed, the in-
tensive function runs for 10', then the appliance go back to
work at the original speed. During this function the display
blinks.
Key E = The Timer times the functions on activation for 15
minutes, after which they are switched off. The Timer is
deactivated by re-pressing Key E. When the Timer is acti-
vated the decimal point must flash on the display. The Timer
cannot be activated if the intensive speed is functioning.
The "clean air" function is activated by pressing key E for
2 seconds when the appliance is switched off. This switches
the motor on for 10 minutes every hour at the first speed.
During functioning a rotary movement of the peripheral
segments must be visualised on the display. When this time
has passed the motor switches off and the fixed letter "C"
must be visualised on the display until the motor re-starts
after 50 minutes for another 10 minutes and so on. Press
any key apart from the light keys to return to normal
functioning. Press key E to deactivate the function.
• Active carbon/grease filter saturation:
- When display item C flashes, at a speed where it
alternates with the letter F (e.g. 1 and F), the grease filters
must be washed.
- When display item C flashes, at a speed where it
alternates with the letter A (e.g. 1 and A), the carbon filters
must be replaced.
After the clean filter has been positioned correctly, the
- 19 -