DeWalt DWE1622 Traducido De Las Instrucciones Originales página 29

d) Remove any adjusting key or wrench
before turning the power tool on. A
wrench or a key left attached to a rotating
part of the power tool may result in personal
injury.
e) Do not overreach. Keep proper
footing and balance at all times. This
enables better control of the power tool in
unexpected situations.
f) Dress properly. Do not wear loose
clothing or jewellery. Keep your hair,
clothing and gloves away from moving
parts. Loose clothes, jewellery or long hair
can be caught in moving parts.
g) If devices are provided for the connection
of dust extraction and collection facilities,
ensure these are connected and properly
used. Use of dust collection can reduce
dust-related hazards.
4) POWER TOOL USE AND CARE
a) Do not force the power tool. Use the
correct power tool for your application.
The correct power tool will do the job
better and safer at the rate for which it
was designed.
b) Do not use the power tool if the switch
does not turn it on and off. Any power
tool that cannot be controlled with the switch
is dangerous and must be repaired.
c) Disconnect the plug from the power
source and/or the battery pack from
the power tool before making any
adjustments, changing accessories, or
storing power tools. Such preventive safety
measures reduce the risk of starting the
power tool accidentally.
d) Store idle power tools out of the reach
of children and do not allow persons
unfamiliar with the power tool or these
instructions to operate the power tool.
Power tools are dangerous in the hands of
untrained users.
e) Maintain power tools. Check for
misalignment or binding of moving parts,
breakage of parts and any other condition
that may affect the power tool's operation.
If damaged, have the power tool repaired
before use. Many accidents are caused by
poorly maintained power tools.
f) Keep cutting tools sharp and clean.
Properly maintained cutting tools with sharp
cutting edges are less likely to bind and are
easier to control.
g) Use the power tool, accessories and
tool bits etc., in accordance with these
instructions taking into account the
working conditions and the work to
be performed. Use of the power tool for
operations different from those intended
could result in a hazardous situation.
5) SERVICE
a) Have your power tool serviced by a
qualified repair person using only identical
replacement parts. This will ensure that the
safety of the power tool is maintained.
Additional Specifi c Safety Rules for
Drill Presses
• Keep your fingers well out of the drill area.
• Always use the drill guard. Before turning on
machine ensure the guard is closed securely.
• Always use the safety chain.
• The magnetic stand is suitable for use on steel
with a thickness starting from 10 mm, with zero
air gap between the magnet core surface and
the mounting surface. Curvature, coats of paint
and surface irregularities will create an air gap.
Keep the air gap to a minimum.
• Always place the machine on a flat surface.
Do not clamp the stand on small or irregularly
shaped objects.
• Always place the machine on a surface that is
clear of shavings, chips, swarf and surface dirt.
• Keep the magnet clean and free of debris and
swarf.
• Do not turn on the machine until it has been
mounted and installed according to these
instructions.
• Do not turn on the machine before having
checked that the magnetic stand has been
tightened firmly to the mounting surface.
• Adjust the table so cutter does not extend into
the workpiece before drilling. Do not perform
any design, assembly or construction activities
on the workpiece while the machine is turned
on.
• Before turning on the machine, make sure the
accessory has been mounted correctly.
• Always use the recommended speed for the
accessories and the material.
• Do not use the machine on the same workpiece
on which electric welders are being used.
• Use only an appropriate cutting fluid. Use a
general metal cutting coolant diluted with water.
• Do not use liquid cutting fluids while drilling
vertically or overhead. Dip the cutter in cutting
paste or apply an appropriate spray for these
applications.
EN G LI SH
27