Elvox Giotto Serie Manual Para El Conexionado Y El Uso página 7

Secondary identification code programming
Programming of the secondary identification code is only required when
more than one monitor is to be called by means of the same pushbutton
or call code. The monitors that ring at the same time are associated with
the same group. The "master" monitor is programmed first by means of
the "identification code programming" procedure described above, while
the additional group monitors are programmed with the secondary iden-
tification code.
A maximum of four monitors can be associated with the same group,
without the need for programmer type 950C.
In the case of monitors, an additional power supply type 6923 must
be fitted for each additional monitor after the second monitor.
Using programmer type 950C, activation of the ringtone on all
monitors can be programmed, without simultaneous activation of
all monitors, to then enable activation of the monitor from the video
entry panel used to answer the call with the self-start pushbutton;
this avoids the need to use additional power supplies.
Programming phase:
1) Press and hold the RESET pushbutton "G" present below the moni-
tor (see Fig 3).
2) Press and hold the lock release pushbutton "D" and self-start
pushbutton "E", together with the RESET pushbutton "G".
3) Release the RESET pushbutton "G", keeping the other two pushbut-
tons pressed.
4) After 2 seconds the monitor emits a high tone, the monitor switches
on and communication is enabled with the panel.
5) Release the lock release pushbutton "D" and self-start pushbutton
"E".
6) On pushbutton entrance panels, press the call button for the
"master" monitor (already programmed), while on alphanumeric key-
pads, enter the call code of the "master" interphone and press
pushbutton " ".
7) When the secondary code is associated with the monitor and com-
munication is terminated.
Pushbutton programming
The monitor is fitted with three pushbuttons for the functions lock relea-
se, self-start and the auxiliary service "stair light", which activates the 1st
relay of the 1st actuator (type 692R), if connected to the system.
To change the operating mode of the self-start pushbutton and auxiliary
service "stair light" use programmer type 950C, with the exception of
assignment of the functions of intercommunicating calls and self-start
service to a specific panel.
During pushbutton programming the ringtone volume control must be in
the ringtone mute position.
Intercommunicating call pushbutton programming
Programming phase:
1) Raise the handset of the interphone or monitor to be called.
2) Press and hold the RESET pushbutton "G" present below the moni-
tor (see Fig 3).
3) Press and hold the additional pushbutton to make the intercommu-
nicating call together with the RESET pushbutton "G".
4) Release the RESET pushbutton "G", keeping the call pushbutton
pressed.
5) After 2 seconds the monitor emits a high tone, while the other inter-
phone/monitor emits a 3-tone ascending scale.
6) Release the intercommunicating call pushbutton.
7) On the interphone/monitor called (with the 3-tone ring), press one of
the programmed pushbuttons (such as lock release, F1 or F2).
8) A high tone confirms the end of the procedure.
Repeat the same procedure for the other interphones/monitors and any
other intercommunicating call pushbuttons.
Programming the self-start pushbutton assigned to a specific panel.
Programming phase:
1) Press and hold the RESET pushbutton "G" present below the moni-
tor (see Fig 3).
2) Press and hold the pushbutton to activate the self-start function toge-
ther with the RESET pushbutton "G".
3) Release the RESET pushbutton "G", keeping the self-start pushbut-
ton "E" pressed.
Press to return to index Press to return to index
P R O G R A M M I N G / O P E R A T I O N
4) After 2 seconds the monitor emits a high tone.
5) Release the self-start pushbutton "E".
6) On pushbutton entrance panels, press the call button for the monitor,
7) A high tone confirms the end of the procedure.
1) Press and hold the RESET pushbutton "G" present below the moni-
2) Press and hold the relative pushbutton to be reprogrammed together
3) Release the RESET pushbutton "G", keeping the other pushbutton
4) After 2 seconds the interphone emits a high tone.
5) Release the pushbutton to restore to default and then press again.
1) Press and hold the RESET pushbutton "G" present below the moni-
2) Press and hold the self-start pushbutton
3) Release the RESET pushbutton "G", keeping the self-start pushbut-
4) After 2 seconds the monitor emits a continuous tone for two seconds.
5) Release the self-start pushbutton "E".
6) During the continuous tone, press the lock release pushbutton "D".
If the deletion procedure is successful, when the lock release tab is pres-
sed the monitor emits a triple "Beep".
OPERATION
Calls from an entrance panel, intercommunicating calls and door calls
are differentiated by means of different tones.
Door calls.
Calls from entrance panels do not follow the pressed pushbutton but are
generated inside the monitor. The call interval is 1 second of ringtone
and 2 seconds of pause repeated twice (default value set on panel). To
answer, raise the handset. If the handset is already raised during the
call, replace and raise it again. The call answer time (30 s) and the con-
versation time (2 minutes by default) are set in the panel parameters.
When the conversation time has elapsed, the user can continue without
replacing the handset if a new call is made within 10 seconds from the
same panel.
Intercommunicating call.
Lift the monitor handset and press the intercommunicating button, if pro-
grammed, for the interphone/monitor to be called. On the handset of the
monitor called, a call tone will ring (if the call is enabled) or an engaged
tone (if not enabled). On the called monitor the ringtone starts sequen-
tially at intervals of 1 second ringing and 4 seconds pause. The maxi-
mum duration of the call is 30 seconds (6 cycles). To answer the call,
simply raise the handset; the maximum duration of the conversation is
60 seconds. When the conversation time has elapsed, the user can con-
tinue without replacing the handset if a new call is made within 10
seconds. Calls from the panel have priority over intercommunicating
calls.
Denied calls.
The variator located below the monitor (Fig. 3) enables modification to
the call volume or to mute the signal. Call mute is indicated by perma-
nent illumination of the red LED. If calls are made to the monitor when
the call mute is enabled, they are denied. A denied call causes the red
Led to briefly switch off according to the number of times calls are denied
(maximum 4 denied calls). The signal is repeated every 10 seconds
(approx.). Deletion of denied calls is by: reenabling the ringtone, reset-
ting the monitor or a system power failure. On the panel, a denied call is
indicated by means of a dissuasion tone (a series of "Beeps" at 100ms
intervals with a pause of 100ms for a total of 5 seconds).
The message "Do not disturb" also appears on panels with display.
while on alphanumeric keypads, enter the call code and press
pushbutton " ".
Restoring default values of pushbuttons.
Programming phase:
tor (see Fig 3).
with the RESET pushbutton "G".
pressed.
Deleting all settings.
Programming phase:
tor (see Fig 3).
RESET pushbutton "G".
ton "E" pressed.
"E" together with the
7