Tabla de contenido
Before operating, stand in the operating position and
check for eye protection, proper clothing, balanced foot-
ing, straight arm, which holds the front-assist handle.
NOTICE:
The trimmer head is parallel to the ground at
a proper cutting distance without the operator bending
over (Fig. N).
For safe and better operation, put on the shoulder strap
across the shoulder as Fig. N. Adjust the shoulder strap
in a comfortable operating position. Hold the line trimmer
with both hands: One hand on the rear handle and the
other hand on the front-assist handle.
There are two ways to release the strap. Take it away
from your shoulder directly (Fig. O) or press the hook of
the strap and take it apart from the shoulder-strap mount
hanger fixed on the shaft (Fig. P).
WARNING:
The shoulder strap is also a quick
release mechanism in
a
hazardous situation. When
an emergency occurs, take it off from your shoulder
immediately, no matter what way the strap is in.
STARTING/STOPPING THE LINE TRIMMER (Fig. M)
To Start
Press down the lock-off lever then depress the trigger.
Different pressure on the trigger results in variable
rotating speed of the cutting line. More pressure, higher
speed.
To Stop
Release the trigger.
NOTICE:
The motor runs only when the lock-off button
and trigger are both pressed.
WARNING:
Always remove the battery pack from
the line trimmer during work breaks and after finishing
work.
Speed Adjustment Function (Fig. M)
The line trimmer has two speeds. Position"1" is for low
speed while Position "2" for high speed. Push or pull
the high/low speed switch to choose the suitable speed
during operation.
Fig. M parts description see below:
M-1 High/low-Speed Switch
M-2 Lock-Off Button
M-3 Trigger
USING THE LINE TRIMMER
WARNING:
To avoid serious personal injury, wear
goggles or safety glasses at all times when operating this
unit. Wear a face mask or dust mask in dusty locations.
Clear the area to be cut before each use. Remove all
objects, such as rocks, broken glass, nails, wire, or line,
that can be thrown or become entangled in the cutting
attachment. Clear the area of children, bystanders,
and pets. At a minimum, keep all children, bystanders
and pets at least 15m away; there still may be risk to
bystanders from thrown objects. Bystanders should be
encouraged to wear eye protection. If you are approached,
stop the motor and cutting attachment immediately.
Before each use, check for damage/worn parts
Check the bump head, guard and front-assist handle
and replace the parts that are cracked, warped, bent, or
damaged in any away.
The line-cutting blade on the edge of the guard can dull
over time. It is recommended that you periodically
sharpen with a file or replace it with a new blade.
guard or servicing the blade. Take care of the blade on the
guard and protect your hand from cutting.
After each use, clean the trimmer.
the air from flowing into the motor housing and result in
overheating or damaged of the motor.
◾
◾
trimmer. Avoid using solvents when cleaning plastic
parts. Most plastics are susceptible to damage from
various types of commercial solvents. Use clean cloths
to remove dirt, dust, oil, grease, etc.
ADJUSTING CUTTING LINE LENGTH
The trimmer head allows the operator to release more
cutting line without stopping the motor. As line becomes
frayed or worn, additional line can be released by lightly
tapping the
the trimmer (Fig. Q).
NOTICE:
cutting line becomes shorter.
blade assembly. Excessive line length will cause the motor
to overheat and may result in serious personal injury.
56 VOLT LITHIUM-ION CORDLESS LINE TRIMMER — ST1530E
WARNING:
Always wear gloves when mounting the
CAUTION:
Obstructions in the vents will prevent
Use only mild soap and a damp cloth to clean the tool.
Never let any liquid get inside the tool; never immerse
any part of the tool into a liquid.
Keep air vents in the motor housing from debris at all
times.
WARNING:
Never use water for cleaning your
trimmer head
on the ground while operating
Line release will become more difficult as the
WARNING:
Do not remove or alter the line cutting
EN
11
Tabla de contenido
