Technical Data - Felisatti APF200/1010E Instrucciones De Servicio

TECHNICAL DATA

Floor and wall sander
Input power
No-load speed
Maximum diameter of sandpaper sheet
Spindle thread
Approx. weight (without acces.)
The instructions contained in this manual must be strictly
followed, it should be carefully read and kept close at
hand to use when carrying out maintenance on the
indicated parts.
If the machine is used carefully and normal maintenance
is carried out, it will work well for a long time.
The functions and use of the tool you have bought shall
be only those described in this manual. Any other use
of the tool is strictly forbidden.
ILLUSTRATIONS
DESCRIPTION (See figures)
A Start-up switch (Fig.1)
B Auxiliary handle (Fig.1)
C Spindle blocking button (Fig.1)
D Cap (Fig.1)
E Brush (Fig.1)
F Interface (Fig.2)
G Velcro plate (Fig.2)
H Dust output (Fig.1)
EQUIPMENT
- 1 auxiliary handle
- 1 cap
- 1 brush
- 1 Velcro plate
- 1 interface
- Operating instructions
- Safety instructions
- Warranty
SAFETY INSTRUCTIONS
 See "Safety Instructions" manual, supplied with this
 WARNING! Material containing asbestos must not be
instruction manual.
polished. Working with materials containing amian-
thus/asbestos and/or silica stones produces a dust,
which is harmful to health. Protect yourself from inhal-
ing this dust, in compliance with current regulations on
 For your personal safety, always connect the machine
accident prevention.
to a mains supply protected by a differential and ther-
mal cutout switch, in accordance with regulations on
 Do not pierce the motor housing as this could damage
low-voltage wiring sitemaps.
 Check the work area with a metal detector for hidden
the double insulation (use adhesive labels).
 Always unplug the machine before carrying out
wires, gas and/or water pipes.
 Always stop the machine by switching it off, not by
work on it.
unplugging it.
W
rpm
mm
ISO
Kg
 WARNING! Before each use, inspect the plug and
lead. Should they need replacing, have this done by an
 Always keep the mains lead clear of the working range
official service centre.
 Only plug the machine in when it is switched off.
of the machine.
 Always use the machine with the auxiliary handle
 Hold the machine firmly in both hands and in a stable
attached.
 Check that the stated disc speed is equal to or greater
position.
 Verify that the disc dimensions are compatible with
than the polisher's rated speed.
 The abrasive discs should be handled and kept with
the polisher.
the utmost care, in accordance with the manufacturer's
 Protect the polisher from knocks, collisions and grease.
instructions.
 Check the disc carefully before use to make sure it is
not damaged or cracked. Replace cracked or dam-
 Make sure the discs are fitted in accordance with the
aged discs immediately.
 Check that the disc has been properly fitted and se-
manufacturer's instructions.
cured before using the machine. Start the machine
with no load and run for 30 seconds in a safe position;
if you notice serious vibration or any other defect stop
the machine immediately. This may be a sign of incor-
 Use only clamps or plates specified for this tool. Do not
rect fitting or a badly balanced disc.
use separate bushings or adapters to adapt grinding
 In machines designed to be used with accessories with
discs with large holes.
threaded holes, check that the thread on the disc is
 Beware of shavings that fly off. Hold the tool that so
long enough to take the length of the spindle.
that sparks fly away from you or other people and in-
 When working on stone, use dust extraction equipment
flammable materials.
 In order for the job to be effective, you should select,
and wear a mask.
based on the material and surface finish, the appropri-
 Do not touch rotating polishing tools.
ate size and abrasive.
 WARNING! The disc will continue to rotate for a time
 When working with the machine, always wear safety
after the machine is switched off.
goggles and ear protection. Other personal protection
equipment such as dust masks, gloves, helmet and
apron should be worn when necessary, along with
non-slip safety footwear. When considering the need
to use a protective mask against the dust, this should
also be for the possible harmful effects of the polished
APF200/1010E
1010
800-1800
200
M14
2.9