Technical Data - Felisatti RGF150/600E Instrucciones De Servicio

TECHNICAL DATA

Rotorbital sander
Input power
No-load speed
Orbits per minute
Max. diameter of the Velcro plate
Oscillation circle
Approx. weight (without acces.)
The instructions contained in this manual must be strictly
followed, it should be carefully read and kept close at
hand to use when carrying out maintenance on the
indicated parts.
If the machine is used carefully and normal maintenance
is carried out, it will work well for a long time.
The functions and use of the tool you have bought shall
be only those described in this manual. Any other use
of the tool is strictly forbidden.
ILLUSTRATIONS
DESCRIPTION (See figures)
A Start-up switch (Fig.1)
B Auxiliary handle (Fig.1)
C Spindle blocking button (Fig.2)
D Velcro plate (Fig.1)
E Electronic regulation control (Fig.1)
F Dust output (Fig.2)
EQUIPMENT
- Operating instructions
- Safety instructions
- Warranty
SAFETY INSTRUCTIONS
 See "Safety Instructions" manual, supplied with this
 WARNING! Material containing asbestos must not be
instruction manual.
polished. Working with materials containing amian-
thus/asbestos and/or silica stones produces a dust,
which is harmful to health. Protect yourself from inhal-
ing this dust, in compliance with current regulations on
 For your personal safety, always connect the machine
accident prevention.
to a mains supply protected by a differential and ther-
mal cutout switch, in accordance with regulations on
 Do not pierce the motor housing as this could damage
low-voltage wiring sitemaps.
 Check the work area with a metal detector for hidden
the double insulation (use adhesive labels).
 Always unplug the machine before carrying out
wires, gas and/or water pipes.
 Always stop the machine by switching it off, not by
work on it.
 WARNING! Before each use, inspect the plug and
unplugging it.
lead. Should they need replacing, have this done by an
 Always keep the mains lead clear of the working range
official service centre.
 Only plug the machine in when it is switched off.
of the machine.
W
rpm
opm
mm
mm
Kg
 Always use the machine with the auxiliary handle
 Hold the machine firmly in both hands and in a stable
attached.
 Check that the speed marked on the disk is the
position.
same or superior to the nominal velocity of the Ro-
 Assure yourself that the dimensions of the disk are
torbital sander.
 The abrasive discs should be handled and kept with
compatible with the Rotorbital sander.
the utmost care, in accordance with the manufac-
 Protect the polisher from knocks, collisions and
turer's instructions.
 Carefully verify the plate in order to assure yourself
grease.
that it is not damaged, nor does it have any cracks
 Assure yourself that the abrasive disks are mounted in
before using it.
 Check that the disc has been properly fitted and se-
accordance with the manufacturer's instructions.
cured before using the machine. Start the machine
with no load and run for 30 seconds in a safe position;
if you notice serious vibration or any other defect stop
the machine immediately. This can indicate a incorrect
 Beware of shavings that fly off. Hold the tool that so
installation or a badly balanced plate.
that sparks fly away from you or other people and in-
 When working on stone, use dust extraction equipment
flammable materials.
 In order for the job to be effective, you should select,
and wear a mask.
based on the material and surface finish, the appropri-
 Do not touch rotating polishing tools.
ate size and abrasive.
 WARNING! The machine maintains itself running
 When working with the machine, always wear safety
during some moments after turning it off.
goggles and ear protection. Other personal protection
equipment such as dust masks, gloves, helmet and
apron should be worn when necessary, along with
non-slip safety footwear. When considering the need
to use a protective mask against the dust, this should
also be for the possible harmful effects of the polished
material and paint or other surface coating. If in doubt,
 Make sure the vents are free when working with dust. If
use safety equipment.
they require cleaning, first unplug the machine, do not
 WARNING: Certain types of dust produced by mechani-
use metal objects and avoid damaging internal parts.
cal polishing, sawing, grinding and drilling, together with
other construction activities, contain chemical agents
which are known to cause cancer, congenital and other
similar defects. Some examples of the chemical agents
RGF150/600E
600
2500-6500
5000-13000
150
5
2.4