Technical Data; Brief Description; Dust Extraction - Felisatti BSF76/900 Instrucciones De Servicio

Belt sander
Rated power
Sanding belt speed
Sanding belt measurements
Acoustic pressure
Sound-power level
Vibration acceleration
Approximate weight
EPTAProcedure 01/00
Follow very carefully the instructions in this manual, save it
and keep it close at hand, ready to carry out any inspection
of parts that may be necessary.
If the machine is used carefully and normal maintenance is
carried out, it will work well for a long time.
The functions and use of the tool you have bought shall be
only those described in this manual. Any other use of the tool
is strictly forbidden.
ILLUSTRATIONS
DESCRIPTION (See figures)
A Lever (Fig.1 & )
B Steel plate (Fig.)
C Adjustment screw (Fig.)
D Sawdust extraction tube (Fig.)
E Dust bag (Fig.)
F Zip fastener (Fig.)
G Blocking button (Fig.)
H Trigger switch (Fig.1 & )
I Speed control (electronic model only) (Fig.)
J Brush holder cover (Fig.)
K Belt direction indicator arrow (Fig.)
EQUIPMENT
- 1 sawdust and shaving collector bag
- 1 sanding belt (610x100) 80 grit
- Operating instructions
- Safety instructions
- Warranty

BRIEF DESCRIPTION

Any use differing from the above is strictly forbidden. Belt
sanders are devices equipped with powerful motors and an
"endless" abrasive belt, which rotates at great speed over two
rollers. These tools are perfectly adapted for grinding large
amounts of material in a short time: for instance, they are
ideal for rough-grinding wood, for rough sanding, for stripping
painted wood... However, they are not at all suitable for
achieving a fine finish.
BEFORE USING THIS TOOL
Before using the tool, make sure the mains voltage is correct:
it must be the same as that on the specification label.
Machines with 0V can also be connected to a 0-V mains


TECHNICAL DATA

(without accessories)
W
m/min
Mm
dB(A)
dB(A)
m/s²
according Kg.
supply.
Before plugging in the tool, always make sure that the trigger
switch works properly and returns to the "OFF" position when
released.
FITTING AND REMOVAL OF THE ABRASIVE BELT
WARNING! Always make sure that the tool is switched off
and unplugged before fitting or removing the belt.
Follow the steps below:
1. Pull out lever A completely and fit the belt over the rollers.
. Make sure that the arrow on the back of the belt points in
the same direction as indicator arrow K on the tool.
3. Once the belt is fitted over the rollers, push lever A back to
its original position.
. Adjust the belt tracking: switch on the tool and make sure
the belt is properly aligned.
5. If the edge of the belt sticks out beyond the edge of the
steel plate B or is more than 6 mm from its inside edge, adjust
the belt tracking with the adjuster screw C.
WARNING! Always make sure that the tool is switched off
and unplugged before fitting or removing the dust bag.
The dust (sawdust) produced while sanding is extracted
into a sawdust collector bag. To fit the bag, follow the steps
below:
1. Fit the collector bag (dust bag) E on the sawdust extraction
tube D.
2. Push it firmly onto the sawdust extraction tube D has far
as it will go to avoid the bag E coming off during operation. If
the machine does not extract all the dust, this is probably due
to the quality or moist charac-ter of the material. Blow off the
moist dust particles.
TIP: For best results we recommend emptying the bag E
when approximately half full and shaking it slightly to remove
as much sawdust as possible.
ELECTRONIC SPEED CONTROL
The electronic speed control I enables the speed of the
sanding belt to be adjusted in different positions num-bered
from 1 al 6. To increase the speed, turn the control I towards
number 6, to decrease the speed, turn towards number 1.
Select the appropriate speed for the finish required and the
part you wish to sand.
BSF76/900 BSF100/1200E
900
50
76 x 5
91,0
10,0
,7
,

DUST EXTRACTION

(only mod. FBS100CE)
100
00-00
100 x 610
96,7
106,7
5,5
5,