Technical Data; Vibration Information; Noise Information - Worx Sonicrafter WX685 Manual De Instrucciones

1. HYPERLOCK™ ACCESSORY CLAMPING
LEVER
2. ON/OFF SWITCH
3. VARIABLE SPEED DIAL
4. CONSTANT SPEED ELECTRONICS
5. VENTING SLOTS
6. UNIVERSAL-FIT ACCESSORY INTERFACE*
7. SMALLER FLANGE (FOR OTHER BRANDS'
SANDING PADS)
8. FLANGE
*Works with other oscillating tool brands'
accessories.
The following brands are trademarks owned by third
parties which may be registered by their respective
owners: Black & Decker
Craftsman , Dremel
®
Imperial Blades, Makita
Performax , Porter Cable
®
Tool Shop .
®
Not all the accessories illustrated or described
are included in standard delivery.
8

TECHNICAL DATA

Type Designation WX685 WX685.11
( 6-designation of machinery, representative of
sonicrafter )
Rated voltage
Rated power
Oscillations speed
Oscillations angle
Protection class
Tool weight (without power cable)

NOISE INFORMATION

A weighted sound pressure
A weighted sound power
K &K
pA wA
Wear ear protection when sound
pressure is over 80 dB (A).
Oscillating Tool
, Bosch , Chicago Electric
® ®
, DeWalt , Fein , Genesis
® ® ®
, Mastercraft , Milwaukee
® ®
, Ridgid , Ryobi , Skil
® ® ®
230-240V~50Hz
12000-21000/min
L
pA
L
wA

VIBRATION INFORMATION

Vibration total values (triax vector sum) determined
according to EN 60745:
Typical weighted
vibration
The declared vibration total value may be used for
comparing one tool with another, and may also be
used in a preliminary assessment of exposure.
WARNING: The vibration emission value
during actual use of the power tool can differ
from the declared value depending on the ways in
which the tool is used dependant on the following
examples and other variations on how the tool is
used:
How the tool is used and the materials being cut or
sanded.
,
®
The tool being in good condition and well maintained
,
®
The use the correct accessory for the tool and
,
®
ensuring it is sharp and in good condition.
, and
®
The tightness of the grip on the handles and if any
anti vibration accessories are used.
And the tool is being used as intended by its design
and these instructions.
This tool may cause hand-arm vibration
syndrome if its use is not adequately managed
WARNING: To be accurate, an estimation of
exposure level in the actual conditions of use
should also take account of all parts of the
operating cycle such as the times when the tool is
switched off and when it is running idle but not
actually doing the job. This may significantly reduce
the exposure level over the total working period.
Helping to minimize your vibration exposure risk.
250W
ALWAYS use sharp chisels, drills and blades.
Maintain this tool in accordance with these
instructions and keep well lubricated (where
appropriate).
3.2°
If the tool is to be used regularly then invest in anti
vibration accessories.
/ll
Avoid using tools in temperatures of 10
Plan your work schedule to spread any high vibration
1.3kg
tool use across a number of days.
OPERATING INSTRUCTIONS
NOTE: Before using the tool, read the
: 84dB(A)
instruction book carefully.
: 95dB(A)
INTENDED USE
3.0dB(A)
The power tool is intended for sawing and
remodelling wooden materials, plastic, plaster, non-
ferrous metals and fasteners (e.g. nails and clamps)
as well as for working on soft wall tiles and for dry
grinding of small surfaces. It is especially suitable for
working close to edges and for flush cutting.
Vibration emission value
a = 3.32m/s
2
h
Uncertainty K = 1.5m/s²
C or less.
O
EN