Tabla de contenido
Idiomas disponibles
Idiomas disponibles
E Saw blade Precision Cut
HW/CT 254 x 30 x 2.4/1.8, , 60 WZ 5° neg.
For very good, clean cutting results for straight
and cross cuts in soft and hard wood. Perfectly
suited for hard wood and plywood, untreated
chipboards, coated or veneered, MDF, composite
materials.
F Saw blade Multi Cut
HW/CT 254 x 30 x 2.4/1.8, 80 FZ/TZ 5° neg.
When high cutting quality is required, e.g.
laminate, plastic, thin-walled aluminium, copper,
and brass profiles Perfect cutting results also for
cross cuts in solid wood, uncoated, coated or
veneered chip board, MDF
G Laminate Cut Professional
254x30 66FZ/TZ 0°
Precise, clean cuts in all types of laminate flooring
thanks to specially developed tooth geometry
H Aluminium Cut Professional
254x30 72FZ/TZ 5°neg
Perfect cuts in aluminium thanks to special tooth
geometry
Saw blades for KGS 315 Plus:
I Saw blade Precision Cut :
HW/CT 315 x 30 x 2.4/1.8, , 48 WZ 5° neg.
For very good, clean cutting results for straight
and cross cuts in soft and hard wood. Perfectly
suited for hard wood and plywood, untreated
chipboards, coated or veneered, MDF, composite
materials.
J Saw blade Precision Cut :
HW/CT 315 x 30 x 2.4/1.8, , 84 WZ 5° neg.
For very good, clean cutting results for straight
and cross cuts in soft and hard wood. Perfectly
suited for hard wood and plywood, untreated
chipboards, coated or veneered, MDF, composite
materials.
K Saw blade Multi Cut :
HW/CT 315 x 30 x 2.4/1.8, 96 FZ/TZ 5° neg.
When high cutting quality is required, e.g.
laminate, plastic, thin-walled aluminium, copper,
and brass profiles Perfect cutting results also for
cross cuts in solid wood, uncoated, coated or
veneered chip board, MDF
See www.metabo.com or the catalogue for a
complete range of accessories.
12. Repairs
Danger!
Repair of power tools must be carried out by
qualified electricians only!
A defective mains cable must be replaced only
with a special, original mains cable from Metabo
available from the Metabo service.
A defective cutting laser must be replaced only
with an original Metabo cutting laser.
If you have Metabo power tools that require
repairs, please contact your Metabo service
centre. For addresses see www.metabo.com.
You can download a list of spare parts from
www.metabo.com.
13. Environmental Protection
Observe national regulations on environmentally
compatible disposal and on the recycling of
disused machines, packaging and accessories.
Only for EU countries: never dispose of
power tools in your household waste!
According to European Directive 2012/19/
EU on Waste from Electric and Electronic
Equipment and implementation in national law,
used power tools must be collected separately
and recycled in an environmentally-friendly
manner.
14. Troubleshooting Guide
Following you will find a description of problems
and faults that you may remedy yourself. If the
corrective measures described here do not help,
kindly refer to chapter 12. "Repairs".
Danger!
There are particularly many accidents in
connection with problems and faults. Therefore
keep in mind:
628222000
· Disconnect the mains plug prior to any fault
service.
· Check to see that all safety devices are
operational after each fault service.
Motor does not run
No mains voltage
628223000
· Check cables, plug, outlet and mains fuse.
Motor overheats (KGS 254 I Plus):
· Remove cause for overheating, let cool down
for a few minutes, then start again.
No trimming function
Transport lock activated:
628446000
· Deactivate transport lock.
Safety lock activated:
· loosen safety lock.
628447000
Cutting power too low
Saw blade blunt (possibly tempering marks on
blade body);
Saw blade unsuitable for the material (see
chapter 11. "Accessories");
628224000
Saw blade contorted:
· Replace saw blade (see chapter 9.
"Maintenance").
Saw vibrates a lot
Saw blade contorted:
· Replace saw blade (see chapter 9.
628225000
"Maintenance").
Saw blade not installed properly:
· Install saw blade properly (see chapter 9.
"Maintenance").
Saw squeaks when starting up
628226000
Drive belt tension too low:
· Tighten drive belt (see chapter 12. "Repairs").
Turntable hard to turn
Chips under turntable:
· remove chips.
15. Technical Specifications
Explanatory notes on the specifications on page 6.
Changes due to technological progress reserved.
U
= Mains voltage
I
= Rated power
F
= Min. fuse protection
P
= rated input power
1
IP
= protection class
SK
= protection rating
n
= No-load speed
0
v
= Max. cutting speed
0
D
= saw blade diameter (outer)
d
= saw blade hole (inside)
b
= max. tooth width of the saw blade
a
= angle range saw head adjustment
1
a
= angle range turntable
2
A
= dimensions (lxwxh)
m
= weight
Requirements for chip and dust extraction unit:
D
= connection diameter of the extraction
1
nozzle
D
= minimum air throughput
2
D
= minimum negative pressure at extraction
3
nozzle
D
= minimum air speed at extraction nozzle
4
Maximum permitted cutting dimensions for
different cuts / maximum cross-section of
workpiece, see table on page 6.
~
AC Power
Machine in protection class II
The technical specifications quoted are subject to
tolerances (in compliance with relevant valid
standards).
Emission values
These values make it possible to assess the
emissions from the power tool and to compare
different power tools. The actual load may be
higher or lower depending on operating
conditions, the condition of the power tool or the
accessories used. Please allow for breaks and
periods when the load is lower for assessment
purposes. Arrange protective measures for the
user, such as organisational measures based on
the adjusted estimates.
Typical A-effective perceived sound levels:
L
= Sound-pressure level
pa
L
= Acoustic power level
WA
K
, K
= Uncertainty
pA
WA
Wear ear protectors!
ENGLISH en
21
Capítulos
Tabla de contenido
