Tabla de contenido
Idiomas disponibles
Idiomas disponibles
en
ENGLISH
Continuous operation: The trigger switch (1) can
be locked using the lock button (2) for continuous
operation. Press the trigger switch (1) again to stop
the machine.
In continuous operation, the machine
continues running if it is forced out of your
hands. Therefore always hold the machine with
both hands using the handle provided, stand
securely and concentrate.
7.4
Working Directions
Sawing:
Use a saw blade geared to the material to be sawn.
SSEP 1400 MVT: Set pendulum motion according
to the applications.
Adapt the stroke rate to the material to the sawn.
SSEP 1400 MVT: Set maximum stroke rate
according to the applications.
Press the machine with the guide (9) against the
workpiece. Switch on the machine, and only then
guide the saw blade against the workpiece.
Do not make contact with any objects or with the
ground with the moving saw blade (danger of
recoil!)
Avoid excessive pressure on the saw blade
(particularly in the case of long saw blades).
If the saw blade jams, turn the machine off
immediately. Widen the sawn gap slightly with a
suitable tool and take out the machine.
After completing the sawing cut, switch off the
machine and only take it out of the sawn gap to
place it down once the saw blade has come to a
standstill (danger of recoil).
Plunge cuts:
Plunge cuts may only be made in soft materials
such as wood or plastic. Only use short saw blades.
Hold the machine with both hands at the intended
handles, take a secure stance and concentrate on
the work.
Set the adjustment lever (4) to the "0" position
(pendulum motion is deactivated).
See illustration B, page 2:
The machine is pressed with the edge of the guide
(9) against the workpiece. The saw blade does not
make contact with the workpiece. Switch on the
machine. The corner of the guide serves as a pivot
point around which the machine is slowly aligned,
whereby the saw blade cuts into the workpiece.
7.5
Sawing close to the wall
Set the adjustment lever (4) to the "0" position
(pendulum motion is deactivated).
See illustration D, page 2.
When sawing near the wall, the saw blade can be
put into the saw blade clamping fixture with the
teeth pointing upwards (contrary to the normal
working position). Ensure that the pendulum action
is deactivated.
10
8. Tips and Tricks
To saw tight curves: Use narrow saw blades.
Sawing metal: To increase the life of the saw
blades, apply cooling lubricant (cooling lubricant
rod 6.23443) along the cutting line.
9. Maintenance
On a regular basis, use compressed air to blow out
the machine through the rear ventilation slots.
Regularly clean the saw blade quick-clamping
fixture (2) and blow out with compressed air. Do not
oil or grease.
10. Accessories
Use only genuine Metabo accessories.
Use only accessories which fulfil the requirements
and specifications listed in these operating
instructions.
See www.metabo.com or the catalogue for a
complete range of accessories.
11. Repairs
Repairs to electrical tools must ONLY be
carried out by qualified electricians!
A defective mains cable must only be replaced with
a special, original mains cable from metabo, which
is available only from the Metabo service.
Contact your local Metabo representative if you
have Metabo power tools requiring repairs. See
www.metabo.com for addresses.
You can download a list of spare parts from
www.metabo.com.
12. Environmental Protection
Observe national regulations on environmentally
compatible disposal and on the recycling of disused
machines, packaging and accessories.
Only for EU countries: Never dispose of
power tools in your household waste! Used
power tools must be collected separately and
handed in for environmentally compatible recycling
in accordance with European Directive 2012/19/EU
on waste electrical and electronic equipment and its
implementation in national legal systems.
13. Technical Data
Explanatory notes on the specifications on page 3.
Changes due to technological progress reserved.
P
= Rated input power
1
P
= Power output
2
I
= Current
n
= Stroke rate at idle speed
0
s
= Stroke length
T
= max. cutting depth (wood)
1
T
= max. cutting depth (metal profiles, metal
2
Tabla de contenido
