Cleaning And Maintenance - GRAPHITE 58G150 Instrucciones De Uso

Taladro atornillador eléctrico

Ocultar thumbs Ver también para 58G150:

Manual del usuario (113 páginas)

página de 84

/ 84
Contenido
Tabla de contenido

Tabla de contenido

WORKING BIT UNTIL IT REACHES THE CORRECT POSITION).

RELEASE THE MOUNTING SLEEVE, WHICH WILL FASTEN THE

WORKING BIT.

THE WORKING TOOL IS REMOVED IN THE REVERSE ORDER TO

THE INSTALLATION.

WHEN SHORT SCREWDRIVER TIPS AND BITS ARE USED, THE

ADDITIONAL ADAPTER FOR SCREWDRIVER BITS MUST BE USED.

ADJUSTABLE HANDLE

THE SCREWDRIVER HANDLE CAN BE POSITIONED STRAIGHT (IN

THE AXIS OF THE SPINDLE) OR AT AN ANGLE. THE HANDLE IS

MAINTAINED IN EACH OF THE POSITION WITH A LATCH.

Press the handle lock button (5).

Rotate the handle by 180

around the axis (fig. E).

Make sure the handle lock button (5) snapped and the handle is

properly secured.

SPINDLE BRAKE

THE CORDLESS SCREWDRIVER IS EQUIPPED WITH AN

ELECTRONIC BRAKE, WHICH STOPS THE SPINDLE IMMEDIATELY

AFTER THE SWITCH BUTTON IS RELEASED. THE BRAKE ENSURES

PRECISION WHEN TIGHTENING OR DRILLING AND PREVENTS

FREE SPINDLE ROTATION AFTER IT IS SWITCHED OFF.

OPERATION / ADJUSTMENTS

SWITCHING ON /SWITCHING OFF

SWITCHING ON - PRESS THE SWITCH BUTTON (9).

SWITCHING OFF - RELEASE THE PRESSURE ON THE SWITCH

BUTTON (9).

SPEED ADJUSTMENT

The drilling or tightening speed can be controlled during work by

increasing or decreasing pressure on the switch button (9). The

speed control allows for a slow start, which prevents a drill from

slipping, when holes are drilled in a dry wall or glazed wall, while it

helps to control the operation during tightening and loosening.

TORQUE ADJUSTMENT

THE SETTING OF THE TORQUE CONTROL RING (2) TO A

SELECTED POSITION LOCKS THE CLUTCH TO A SPECIFIED

AMOUNT OF TORQUE. WHEN THE SET AMOUNT OF TORQUE IS

REACHED, THE OVERLOAD CLUTCH WILL BE AUTOMATICALLY

DISCONNECTED. THIS PREVENTS FROM OVERTIGHTENING OF A

SCREW OR DAMAGING THE TOOL.

DIFFERENT VALUES OF TORQUE ARE APPLIED TO VARIOUS

TYPES OF SCREWS AND MATERIALS. THE HIGHER IS THE

NUMBER CORRESPONDING TO A GIVEN POSITION, THE HIGHER

IS THE TORQUE.

Set the torque control ring (2) to a specified amount of torque (fig.

F).

The work should be started with a lower value of torque.

Increase the torque gradually until appropriate value is set (range

0 ÷ 10).

Higher settings should be used to loosen screws.

The ability to select proper torque settings comes with practice.

The setting of the torque control ring to the drilling position

deactivates the overload clutch.

ROTATION DIRECTIONS - LEFT AND RIGHT

THE DIRECTION OF SPINDLE ROTATIONS IS SELECTED BY

MEANS OF THE ROTATION DIRECTION SWITCH (6) (FIG. G).

LEFT ROTATIONS - SET THE ROTATION DIRECTION SWITCH (6)

IN THE EXTREME LEFT POSITION.

RIGHT ROTATIONS - SET THE ROTATION DIRECTION SWITCH (6)

IN THE EXTREME RIGHT POSITION.

* It is reserved that in some cases the position of the rotation

direction switch in relation to rotations may be different than

described. Refer to graphic signs located on the rotation direction

switch or on the tool casing.

The middle position of the rotation direction switch (6) is a safe

position that prevents accidental activation of the power tool:

The screwdriver can not be activated in this position.

Bits and drills are replaced in this position.

Before the tool is activated, make sure the rotation direction switch

(6) is set to a correct position.

The direction of rotations can not be changed, when the

screwdriver spindle rotates.

Long-lasting drilling with low torque of the spindle may overheat

the motor. Periodical breaks in operation must be taken or

allow the tool to operate with maximum speed without load

for approximately 3 minutes.

OPERATION AND MAINTENANCE