Tabla de contenido
Rechargeable Li- ion batteries can leak, ignite, or explode if
heated to high temperatures or shorted out. They should not be
stored in the car on hot and sunny days. Do not open the
battery. Rechargeable
Li- ion
safety devices which, if damaged, may cause the battery to
ignite or explode.
Explanation of the pictograms used.
1. Read the operating manual, observe the warnings and
safety conditions contained in it!
2. Use protective
glasses
3. Protect against moisture and rain.
4. Disconnect from the power source before maintenance
or repair
5. Do not allow it to heat above 50 ° C.
6. Do not throw cells into fire.
7. Hazardous to the aquatic environment.
8. Keep children away from the device
9. Second class of protection.
CONSTRUCTION AND APPLICATION
Cordless screwdriver can be used with many driver tips and bits of
various lengths with hexagonal shanks of 6.35 mm (1/4") in size. The
tool is designed mainly as a screwdriver, it can also be used with
sockets and drills with hexagonal shanks (6.35 mm) for light drilling
works (e.g. making of pilot holes).
Cordless, battery-powered power tools are especially useful for
works in interior furnishing, adaptation of premises etc.
The power tool should be used according to its purpose.
DESCRIPTION OF GRAPHIC PAGES
The below list refers to device components shown in the graphic
pages of this instruction manual.
1. Tool chuck:
2. Torque adjustment ring
3. Battery charge indicator
4. Battery charge indicator button
5. Handle lock
6. Speed direction switch
7. Charger socket
8. Charging indicator (LED)
9. Switch
10. Lighting button
11. Lighting (LED)
* There can be differences between the drawing and real product.
batteries contain
electronic
EQUIPMENT AND ACCESSORIES
Charger
Screwdriver bits
Screwdriver bit adapter
Carry case
PREPARATION FOR WORK
BATTERY CHARGING
THE SCREWDRIVER IS SUPPLIED WITH A PARTIALLY CHARGED
BATTERY. IT IS RECOMMENDED TO CHARGE IT FOR 5 HOURS
FOR THE FIRST TIME. THE BATTERY SHOULD BE CHARGED IN
AMBIENT TEMPERATURES RANGING FROM 4°C TO 40°C.
INSERT THE CHARGER CORD PLUG INTO THE CHARGING
SOCKET (7) IN THE SCREWDRIVER CASING (FIG. A).
Connect the charger to a mains socket of 230V AC.
The charging indicator (LED) (8) will be lit on the screwdriver casing
to signal that charging is under way (fig. B).
The charging indicator (LED) will remain lit as long as the battery is
charged and will go off to signal that the battery is fully
charged.
The battery should not be charged longer than 8 hours.
Exceeding this time limit may cause damage to battery cells.
The screwdriver battery has the so called "sleeping" function,
which means that, when unused, the screwdriver deactivates all
unnecessary circuits to save battery power. The battery charge
level can not be checked and the lighting can not be switched
on in this phase. When the switch button is pressed for a short
time, all functions will be restored.
Batteries become heated, when they are charged. Do not
commence any works, just after the battery was charged. Wait
until it reaches room temperature. This will prevent the battery
from damage.
BATTERY CHARGE LEVEL INDICATION
THE SCREWDRIVER IS EQUIPPED WITH BATTERY CHARGE LEVEL
INDICATOR (LEDS) (3). THREE LEDS INDICATE THE BATTERY
CHARGE LEVEL. IN ORDER TO CHECK THE BATTERY CHARGE
LEVEL:
Press the charge level indicator button (4) (fig. C).
When all three LEDs are lit, it means that the battery is fully
charged.
When two LEDs are lit, it means that the battery is partially
discharged.
When only one LED is lit, the battery is discharged and it must be
charged.
LIGHTING
EACH TIME THE LIGHTING BUTTON IS PRESSED (10), THE
LIGHTING LED IS SWITCHED ON/OFF (11) THAT LIGHTS
WORKING AREA (FIG. D).
INSERTING / REMOVING WORKING BITS
PULL OF THE TOOL CHUCK SLEEVE (1) OVERCOMING THE
SPRING RESISTANCE.
INSERT A WORKING BIT SHANK TO THE CHUCK (1), INSERTING
IT ALL THE WAY (IT MAY BE NECESSARY TO ROTATED THE
9
- 1 pcs
- 18 pcs
- 1 pcs
- 1 pcs
Tabla de contenido
