Connection Panel Fsa 500; Led Indicators; Remote Trigger - Bosch FSA 500 Manual Original

3.5.3

Connection panel FSA 500

DANGER – Risk of electric shock from
excessively high measurement voltage!
The measurement of voltages in excess of
200 V using CH1 / CH2 multi measurement
cables will result in injury, heart failure or
fatal electric shocks.
¶
CH1 / CH2 multi measurement cables are
only to be used for measuring voltages up
to max. 200 V.
¶
Never use CH1 / CH2 multi measurement
cable to measure mains or similar
voltages.
459903-02_Ko
1 2 3 4 5
Fig. 2: Connection panel FSA 500 (viewed from underneath)
Item Color code Connection
1 Red/black Battery B+/B‒ cable
(battery B– cable for vehicle
ground)
2 Green or Secondary measuring sensor or 30 A
white or amps clamp or 1000 A amps clamp
yellow or adapter cable 1 681 032 098 with
fluid pressure sensor (both special
accessories)
3 Green or red CH2 multi measurement cable
or yellow or 30 A amps clamp or
1000 A amps clamp
4 Green or blue CH1 multi measurement cable
or yellow or 30 A amps clamp or
1000 A amps clamp
5 - Coupling with hose assembly
(atmospheric pressure
measurement)
6 -

Remote trigger

7 White/black Clip-on sensor or adapter
cable 1 684 465 513 for clip-on
sensor1)
8 Blue/white Oil temperature sensor, air and
IR temperature sensor (special
accessories)
9 Yellow / Connecting cable term. 1/term.
green 15/EST/TN/TD
10 - Power supply port
11 - - Connection for charging station
(special accessory)
For speed measurements with a clip-on sensor, the adapter cable
1)
1 684 465 513 must always be connected between the FSA 500
socket (item 7) and the connection cables for the clip-on sensor.
The color codings on the connection cables refer to the correct
2)
connection at the FSA 500.
Robert Bosch GmbH
6
7 8 9 10 11
2)
Product description | FSA 500 | 23 |
3.5.4

LED Indicators

LED A: Status light
State LED A
Not lit FSA 500 off.
Red light The FSA 500 starts up.
Flashing FSA 500 on, but not yet ready for operation.
white No data link with PC/Laptop.
(1 Hz)
Flashing FSA 500 is ready for operation.
green Data link to PC/Laptop established via USB.
(1 Hz)
Flashing FSA 500 is ready for operation.
blue Data link to PC/Laptop established via Bluetooth.
(1 Hz)
Flashing Firmware error.
red FSA 500 not ready for use.
(4 Hz)
LED B: Charge indicator
State LED B
Not lit No external power
supply connected.
Voltage supply via
battery.
Violet light External voltage supply
connected. Storage
battery being charged.
Blue light External voltage supply
connected. Storage
battery is charged.
Red light External voltage supply
connected.
Possible cause of
trouble:
R Battery temperature
>45 °C
R Storage battery not
connected
R Battery defective
R Plug defective
3.5.5 Remote trigger
The start soft key (F3) or the stop soft key (F4) in the
FSA 500 CompacSoft [plus] software can be activated
with the button on the remote trigger.
2
1 684 463 828
Fig. 3: Remote trigger (1 684 463 828)
1 Key
2 Connector for FSA 500
i
For connection see fig. 2, item 6.
en
Measure
-
-
External voltage supply
can be disconnected.
Check storage battery
and plug.
Allow the FSA 500 to
cool down.
1
459903-04_Ko
|
1 689 989 411 2021-02-24