After Operation; Routine Maintenance; Battery Power Reserve; General Information - GGP ITALY Cruiser 430 Li 80 Serie Manual De Instrucciones

Always stop the machine:
– when moving between work areas; – when driving on grass free surfaces;
– every time it is necessary to overcome an obstacle;
– before adjusting the cutting height.
– whenever you remove or reattach the grass catcher;
– whenever you remove or reattach the
side discharge chute (if provided);
6.6

AFTER OPERATION

1. Stop the machine (par. 6.5).
2. Open the hatch (fig. 17.A) and remove
the safety key (fig. 17.B).
3. Recharge the battery (par. 7.2.2).
4. Allow the motor to cool before storing
in an enclosed space.
5. Clean (par. 7.3).
IMPORTANT Remove the safety key whenever
the machine is unused or left unattended.
7.

ROUTINE MAINTENANCE

7.1

GENERAL INFORMATION

The safety regulations to follow are
described in chap. 2. Strictly comply with these
instructions to avoid serious risks or hazards.
Before conducting any inspections,
cleaning or maintenance/adjustment
interventions on the machine:
• stop the motor;
• remove the safety key, (never leave the
key in the ignition or within reach of
children or unauthorised persons);
• make sure that all moving parts have
come to a complete stop;
• read the relevant instructions;
• Use suitable clothing, protective
gloves and goggles.
• The frequency and types of maintenance are
summarised in the "Maintenance Table". The table
will help you maintain your machine's safety and
performance. It lists the main maintenance tasks and
how often they need to be performed. Carry out the
relevant task as soon as it is scheduled to be performed.
• The use of non-genuine and/or incorrectly
assembled spare parts and attachments could
adversely affect machine operation and safety. The
manufacturer shall decline all liability in the event
of injuries or damages caused by such parts.
• Genuine spare parts are supplied by authorised
assistance workshops and dealers.
7.2 BATTERY
7.2.1

Battery power reserve

Battery power reserve (and therefore the mowable lawn
surface before recharging is required) mainly depends on:
a. environmental factors, that cause
higher energy requirements:
– mowing dense, high and/or wet grass;
b. operator behaviour, who should avoid:
– switching the machine on and off
frequently whilst working;
– setting a cutting height that is too
low for the lawn conditions;
– working at a speed that is too high in relation
to the amount of grass to be removed.
To optimise battery power reserve it
is always recommended to:
• cut the grass when the lawn is dry;
• cut the grass frequently so that it doesn't grow too tall;
• set a higher cutting height when the grass is very tall,
then set a lower height and cut the lawn again;
• do not use the machine in "mulching"
mode when the grass is very tall.
If the need arises to use the machine for sessions which
exceed the capability of a standard battery, it is possible to:
• purchase a second standard battery to immediately
replace the worn down battery, without
compromising the continuity of operations;
• purchase a battery with an extended power reserve
compared to the standard version (par.
7.2.2 Battery removal and recharging
1. Open the battery housing hatch (fig. 17.A)
and remove the safety key (fig. 17.B);
2. press the side flap in the battery housing (fig.
18.A) and remove the battery (fig. 18.B);
3. insert the battery (fig. 18.B) into its housing
in the battery charger (fig. 18.C);
4. connect the battery charger (fig. 18.C) to a power
socket with the voltage indicated on the rating plate;
5. fully charge the battery according to the instructions
in the battery/battery charger booklet.
NOTE The battery is equipped with a guard
that inhibits recharging if the environmental
temperature is not between 0 and +45 °C.
NOTE The battery can be recharged at any
time, even partially, with no risk of damaging it.
7.2.3 Refitting the battery on the machine
When recharging is completed:
1. Remove the battery (fig. 19.A) from the
housing in the battery charger (do not keep
recharging when recharging is completed);
disconnect the battery charger
2.
(fig. 19.B) from the mains;
3. open the battery housing hatch (fig. 19.C),
insert the battery (fig. 19.A) into its housing
EN - 8
15.2).