Technical Data; Safety Instructions - AEG TS 250 K Manual Original

TECHNICAL DATA

Rated input ...............................................................................
Rated current ............................................................................
No-load speed ..........................................................................
Saw blade dia. x hole dia...........................................................
Saw blade thickness .................................................................
Cutting depth at 90° ..................................................................
Cutting depth at 45° ..................................................................
Weight without cable .................................................................
Noise/Vibration Information
Measured values determined according to EN 61029.
Typically, the A-weighted noise levels of the tool are:
Sound pressure level ............................................................
Sound power level ................................................................
Wear ear protectors!
WARNING!
GB GB
Read all safety warnings and all instructions, including those
given in the accompanying brochure. Failure to follow the warnings
and instructions may result in electric shock, fire and/or serious
injury. Save all warnings and instructions for future reference.

SAFETY INSTRUCTIONS

Wear ear protectors. Exposure to noise can cause hearing loss.
Appliances used at many different locations including open air
should be connected via a residual current device (FI, RCD,
PRCD) of 30mA or less.
Always wear goggles when using the machine. It is recommended to
wear gloves, sturdy non slipping shoes and apron.
Always disconnect the plug from the socket before carrying out any
work on the machine.
Only plug-in when machine is switched off.
Keep mains lead clear from working range of the machine. Always
lead the cable away behind you.
Sawdust and splinters must not be removed while the machine is
running.
Remove adjusting keys and wrenches. From habit of checking to
see that keys and adjusting wrenches are removed from tool before
turning it „ON".
Adjust the riving knife as described in this instruction manual.
Incorrect spacing, positioning and alignment can make the riving
knife ineffective in preventing kickback.
The teeth thickness, or the set of the teeth must be thicker than the
body of the blade and the riving knife. Do not remove the riving knife.
Only move the workpiece in counter rotation to sawblade (only work
oppositely oriented)! For security, use devices such as safety- and
pressure device, guide slide, rip fence, etc.
Always keep hands away from the path of the saw blade.
Never reach into the danger area of the plane when it is running.
Move the rip fence out of the way when cross-cutting
Never use the fence as a cut-off gauge when cross-cutting.
When blade is binding, or when interrupting a cut for any reason,
release the trigger and hold the saw motionless in the material
until the blade comes to a complete stop. Never attempt to remove
the saw from the work or pull the saw backward while the blade is
in motion or kickback may occur. Investigate and take corrective
actions to eliminate the cause of blade binding.
English
20
........................................................................1800 W
...........................................................................7,5 A
........................................................................4800 min
.................................................................. 250 x 30 mm
...........................................................................1,8 mm
............................................................................90 mm
............................................................................62 mm
............................................................................41 kg
............................................................................98 dB(A)
..........................................................................111 dB(A)
Support large panels to minimise the risk of blade pinching and
kickback. Large panels tend to sag under their own weight.
Supports must be placed under the panel on both sides, near the
line of cut and near the edge of the panel.
Do not use dull or damaged blades. Unsharpened or improperly
set blades produce narrow kerf causing excessive friction, blade
binding and kickback.
Keeping rip fence parallel to the saw blade.
Before use check machine, cable, and plug for any damages or
material fatigue. Repairs should only be carried out by authorised
Service Agents.
Always use the protective shields on the machine.
Do not clamp the protective swing guard.
Do not use saw blades which are damaged or deformed
Replace the table insert when worn
Before using the tool please read the instructions. If possible have
the tool demonstrated.
The dust produced when using this tool may be harmful to health.
Do not inhale the dust. Use a dust absorption system and wear a
suitable dust protection mask. Remove deposited dust thoroughly,
e.g. with a vacuum cleaner.
Do not use saw blades not corresponding to the key data given in
these instructions for use.
Do not use saw blades made of high-speed steel.
Any faults with the machine, including any related to the safeguard
or the saw blades, must be reported to the persons in charge of
safety as soon as the faults are discovered.
It is necessary to select a saw blade which is suitable for the
material being cut.
Never use the circular table saw to cut materials other than those
specified in the instruction manual.
The handle lock must always be engaged when transporting the
circular table saw.
Only use the saw with guards in good working order and properly
maintained, and in position.
When sawing thin stock layed on edge, a suitable auxilary fence
must be used for firm support.
Keep the floor area free of loose material e.g. chips and cut-offs.
Only use saw blades which have been properly sharpened. It is
essential to adhere to the maximum speed specified on the saw
blade.
Circular table saw
TS 250 K
-1