Type Of Use And Contraindications; Technical Specifications; Noise Conditions; Removal Of Package - Femi D 305 Manual Del Usuario

EN

TYPE OF USE AND CONTRAINDICATIONS.

This machine has been designed and manufactured for
cutting operations in mitre saw or bench saw mode.
PERMITTED USE
This machine, with suitable blades installed, may be used
in mitre saw or bench saw mode for cutting:
• SEASONED WOOD
This machine, with suitable blades installed, may be used
in mitre saw mode only for cutting:
• PLASTIC MATERIALS
• ALUMINIUM AND ITS ALLOYS
FORBIDDEN USE
It is forbidden to cut:
• MAGNESIUM
• FERROUS MATERIALS
• ORGANIC MATERIALS AND/OR FOOD STUFFS
• MATERIALS WHICH MAY, UPON CUTTING, RELEASE
TOXIC SUBSTANCES.
• IT IS STRICTLY FORBIDDEN TO CUT DAMP WOOD
WHEN USING THE MACHINE IN BENCH SAW
MODE.
• IT IS STRICTLY FORBIDDEN TO USE THE MACHINE
TO MAKE BLIND CUTS.
• IT IS STRICTLY FORBIDDEN TO CUT METAL
MATERIAL WHEN USING THE MACHINE AS A
CIRCULAR SAW.
PERSONNEL AUTHORIZED TO USE THE MACHINE
This machine has been designed and manufactured to
be used by qualifi ed personnel with adequate training,
experience and skills. Below you will fi nd a list of basic
requirements:
Operators / Trainees / Apprentices:
• may be male or female
• must be aged 14 or over
• must have full use of both hands
• must have no physical or mental disabilities
• must know and fully understand the contents of the user
manual-
PERMITTED AMBIENT CONDITIONS
Ambient condition operating limits:
• operating ambient with a temperature between + 5°C – +
40°C
• relative humidity 50 % at a maximum temperature of +
40 °C at a maximum altitude of 1,000 m a.s.l.
• the machine must be used in an environment which is
protected from the elements
CAUTION
Despite the machine not having a signifi cant
environmental impact, it is in any case up to the
user to evaluate machine use to minimize any
possible negative consequences.
WARNING
THIS MACHINE IS NOT SUITABLE FOR USE IN
POTENTIALLY EXPLOSIVE ENVIRONMENTS.
18

TECHNICAL SPECIFICATIONS

Engine power: ....................................................2000 W S1
Voltage and frequency: ..................................230 V - 50 Hz
Speed: .................................................................4200 RPM
Saw blade maximum dimensions: ......305x30X2,8 mm (40
teeth)
Crosscut at 90°: ............................................. 185 X 85 mm
Oblique cutting 45°: ........................................ 125 X 85 mm
Inclined cutting 45°: ........................................ 185 X 60 mm
Oblique cutting 45°: ...........................................90 x 40 mm
Left and right stops:.................................. 0° - 45° every 5°
Inclination stops: .................................................. 0 and 45°
Net weight: ...............................................................17.5 kg
Gross weight: .............................................................. 19 kg
Hand-arm vibration: ........................................< 2,5 m/sec2

NOISE CONDITIONS

The noise emitted, measured in conformity with the standards
EN61029, EN3744 and EN11201 is:
- Sound pressure level .......................... LpA = 100 dB(A)
- Sound power level ............................. LWA = 113 dB(A)
- Uncertainty of measurement K ................................ 3 dB
We recommend you to use ear protection devices.
The sources of the noise of the saw are: the electric engine
and its ventilation system, the speed reduction device, the
blade and the material to be cut.
We advise you to control the engine, its ventilation system
and the aspiration passages. As far as the saw blade is
concerned, it is preferable to use silenced type of blades
and to keep them in good conditions. We recommend to
use the correct saw blade and to keep fi rmly the workpieces
to be cut.
Noise levels are emission levels and do not necessarily
indicate safe working conditions. Even if there is a connection
between emission levels and exposure levels, the fi rst ones
cannot be used to determine safely if other precautions
are necessary. The factors that can infl uence the actual
exposure level of the operator include the exposure length,
environmental features and other sources of noise, as for
example the number of machines and operations in the
surrounding area. Besides, exposure levels can change
from country to country. However, these instructions enable
the user of the machine to better evaluate the dangers and
risks.

REMOVAL OF PACKAGE

The parts included in the package are:
– Mitre saw
– Wrenches for replacing the blade
– 5 mm Allen wrench
– Additional lower protection
– Pusher
– Mitre gauge included in the fence
– Vertical clamp
– Dust collection sack
– Workbench extension
– Bar stop rod